20
USE AND CARE INSTRUCTIONS
Brush soapy solution onto LP Gas tank in the ar-
eas indicated by the arrows. See diagram.
If growing bubbles appear do not use or move the
LP Gas tank. Call an LP Gas Supplier or your Fire
Department.
NOTE about LP Gas Tank Exchange Programs
Many retailers that sell grills offer you the option of
replacing your empty LP Gas tank through an exchange
service. Use only those reputable exchange compa-
nies that inspect, precision fill, test and certify their
tanks. Exchange your tank only for an OPD safety fea-
ture-equipped tank as described in the LP Gas tank
section of this guide.
Ÿ
How to Leak Test your LP Gas Tank
Use a clean paintbrush and a 50/50 mild soap and
water solution.
Ÿ
Ÿ
Ÿ
For your safety:
Leak test new and exchanged LP Gas tanks BEFORE
connecting one to your grill.
Always keep new and exchanged LP Gas tanks in an
upright position during use, transit or storage.
All leak tests must be repeated each time your LP
Gas tank is exchanged or refilled.
When checking for gas leaks do not smoke.
Do not use an open flame to check for gas leaks.
Your grill must be leak tested outdoors in a well-ven-
tilated area, away from ignition sources such as gas
fired or electrical appliances. During the leak test, keep
your grill away from open flames or sparks.
Do not use household cleaning agents. Damage to
gas assembly components can result.
Ÿ
Ÿ
Ÿ
Ÿ
If growing bubbles appear do not use or move the
LP Gas tank. Contact an LP Gas Supplier or your
fire department!
WARNING
!
!
Secure a 20lb LP Gas Tank to Gas Grill
(for BTE26(A,B)LP, BTE3212(A,B)LP & BTE3812BLP)
NOTE:
When using Liquid Propane, EXTREME CAU-
TION should be used to provide ample ventilation of
vapor from the enclosure. LP Gas vapor is heavier
than air
and SERIOUS INJURY from a DANGEROUS
EXPLOSION could occur if LP Gas is allowed to
accumulate in an enclosure and then ignited. Both the
Barbecue enclosure and LP cylinder enclosure re-
quire venting that must be provided at the floor level
of the enclosure to allow any leaking LP Gas vapor
to escape (see Fig. 1).
NOTE:
When installing a barbecue equipped for liquid
propane(LP) in an island, the propane tank must be
in a separate enclosure that is completely isolated
from the barbecue. It must be cross-ventilated in
accordance with the current standards. The propane
tank MUST NEVER be installed directly under the
barbecue.
NOTE:
The total of the upper ventilation openings
must be a minimum of 20 sq. inches. The total of
the lower ventilation openings must be a minimum
of 10 sq. inches. Upper and lower ventilation open-
ings MUST BE PROVIDED on both sides of built-in
construction. The top of the upper ventilation openings
must be located within 5" from the top of the island.
The bottom of the lower ventilation openings must be
at least 1" or less from the floor of the island. The
top of the lower ventilation openings cannot be more
than 5" from the floor of the island. Every ventilation
opening must be a minimum of 1/8". (See Fig. 6 on
page 17). Please ask a Grand Hall associate for more
details.
LP Gas Model only:
Note: You can only use a 20lb LP Gas Tank
in this Gas Grill.
Fig. 1
5/8" UNF Male
Thread
Air Vents
CSA Approved Stainless
Steel Flexible Connector
Air Vents
Non-Combustible
Construction, such as
stone, marble, cement
Clamp down
flexline
The built-in appliance for use with a remote self-contained LP
Gas supply system must use rigid pipe, semi-rigid tubing or a
connector complying with the Standard for Connections for
Gas Appliances, ANSI Z21.24/CSA6.10, or the standard for
Connectors Outdoor Gas Appliance and Manufactured
Homes, ANSI21.75/CSA 6.27 and suitable for outside installa-
tion. The maximum length of the connection shall be 6 ft(1.82m).
The connector should be installed at the location visible
when opening the door.
The connector must be away from any sharp points or sharp
edges.
When using semi-rigid tubing, do not use materials made of
aluminium or aluminium alloy.
Note: