Turbo Ace AllSteady 5 Скачать руководство пользователя страница 7

6

 

 

II. Battery & Charger

 

 

Your AllSteady-5 comes with a smart lithium ion battery. There is a built-in controller in each battery pack 
that monitors the voltage during charging and discharging so you will never have to worry about under or 
overcharging. It will take approximately 2 hours to charge an empty battery. 

 

WARNING BEFORE USE 

**Never 

leave charger unattended, exceed maximum charge rate, charge with non-approved batteries or 

charge batteries in the wrong mode.  

**Always 

ensure the battery you are charging meets the specifications of this charger and that the charger 

settings are correct. Not doing so can result in excessive heat and other related product malfunctions, which 
can lead to user injury or property damage. 

PLEASE DO NOT… 

 

…leave the power supply, charger and battery unattended during use. 

 

attempt to charge dead, damaged or wet battery packs. 

 

…attempt to charge a battery pack containing different types of batteries. 

 

…allow minors to charge battery packs. 

 

…charge batteries in extremely hot or cold places or place in direct sunlight. 

 

…charge a battery if the cable has been pinched or shorted. 

 

…connect more than one battery pack to this charger at a time 

 

…connect the charger if the power cable has been pinched or shorted. 

 

…connect the charger to an automobile 12V battery while the vehicle is running. 

 

…attempt to dismantle the charger or use a damaged charger. 

 

…reverse the positive and negative terminals. 

 

…connect to AC power. 

KEEP IN MIND TO ALWAYS… 

 

…power on the charger before connecting the battery 

 

…use only rechargeable batteries designed for use with this type of charger. 

 

…inspect the battery before charging. 

 

…keep the battery away from any material that could be affected by heat. 

 

...monitor the charging area and have a fire extinguisher available at all times. 

 

…end the charging process if the battery becomes hot to the touch or starts to change form (swell) 
during the charge process. 

 
 
 
 
 

Содержание AllSteady 5



















Отзывы: