Tunstall Macon AB Series Скачать руководство пользователя страница 149

Страница: 149 / 155

Flexible Hoses

Installation:

1. Adhere to allowable radius of bend. (See table below)

2. Verify the installation conditions do not cause torsion of flexible. (See figure1 below)

3. If necessary modify the installation in the event that it is not possible to adhere to the allowable radius of bend (see

paragraph 1 below). For example, add an intermediary right angle fitting (See figure 2 below).

4. Do not submit the connectors to tension, either from the installation, or as a result of pressure or expansion (see figure

3 below).

4. The braiding of the flexible must never be in contact with cement, plaster or all other materials or fluids capable of

causing corrosion.

INSTALLATION & OPERATION

INSTRUCTIONS

ON INSTALLATION: Avoid absolutely any tension due

to stretching during the course of tightening the

connectors. Do not turn fittings in the hose. Do not twist

hose. Avoid sharp bends, kinking or twisting of the hose

during installation. The ½”, 3/4” and 1” hose connection

is a metal to metal seal. The brass mating surfaces

should be smooth and free of debris. The 1-1/4”, 1-1/2”

and 2” hose connection use a specially design gasket,

do not install without the gasket. Do not use pipe dope

or tape sealants on the metal to metal or gasket

connection adapters when connecting to the swivel nut.

A. Install and tighten the fixed male connector.

B. Remove the swivel adapter from the swivel nut.

Install and tighten the union adaptor.

C. Install and tighten the adapter to the swivel nut.

Use two spanners in order to screw the union together:

One to hold the hexagon of the adaptor.

The other to tighten the nut at the same time.

IMPORTANT: Do not re-screw the fixed connector or

adaptor after tightening of the swivel nut ; this will cause

tensioning of the flexible with a risk of rapid deterioration

at this point.

On removal, take precautions. If the flexible

incorporates two fixed connectors, at least one must be

installed on a counter-part fitting with a swivel connector

or a union, if not installation is impossible.

INSPECTION: Hci recommends a good maintenance

practice and periodic inspections, typically when

servicing other components at the unit or at the

installation site. Check all hoses for small water leaks,

residue, discoloration on the exterior braid and fittings.

If a leak is detected, stop service to the unit and replace

hose immediately. Do not attempt to the repair hose.

Caution: Introduction of chemicals into the system or

unit may cause damage to the inner core of the hose.

Consult a water treatment specialist for chemical

compatibility before using any chemical additives.

Warning: Hoses are designed for hydronic heating and

cooling service only, not for gas.

Tunstall Corporation
118 Exchange Street Chicopee, MA 01013

Phone: (413) 594-8695 Fax: (413) 598-8109
www.tunstall-inc.com

INSTALLATION & OPERATION

INSTRUCTIONS

INSPECTION: Macon recommends a good maintenance

149

Содержание Macon AB Series




























































































































































Результаты поиска

Содержание Macon AB Series

Отзывы:

Tunstall Macon AB Series, Руководство пользователя, Страница: 149 / 155

Результаты поиска

Содержание Macon AB Series

Отзывы: