Tunstall Macon AB Series Скачать руководство пользователя страница 146

Страница: 146 / 155

PAGE 2

INSTALLATION & OPERATING INSTRUCTIONS

FLANGE VALVE CONNECTIONS

Class 150 Valves are mechanically compatible with

standard ANSI 150 lb, flat-faced or raised-faced steel

flanges or with 125lb, cast iron flanges.

Appropriated gasket material must be used when

installing flanged-mounted flow control devices

(for example 1/16” thick ring type fiber filled gaskets).

(Not supplied by Macon). All products have a flow

direction arrow. Make sure that it is pointing in the

direction of the flow.

Installing the butterfly Valve:

Do not use flange gaskets.

The molded valve gasket will seal against the

standard ANSI flanges.

Before tightening any bolts on the butterfly valve,

turn the disk of the butterfly to the full open position.

Center the valve and hand tighten all bolts. Slowly

close the disk to check for adequate disk clearance.

When properly aligned, return the disk to the open

position and evenly cross-tighten all bolts. Make sure

the disk opens and closes properly.

Grease the pipe ends, valve ends and rubber gasket

lips with grease, graphite paste or similar grease.

Slip the rubber gasket over the pipe end of each joint.

Slide the gasket past the grooves. Position the grooved

end valve between the pipe ends and slide the gaskets

back into the central spanned position.

All products have a flow direction arrow. Make sure that

it is pointing in the direction of the flow. Apply grease

on the outside of the gasket. Install housing clamps

over the gasket – insert bolts and nuts.

Tighten nuts evenly, using socket or other wrench.

Tighten so that housing clamps come together evenly.

The connection is complete when housing clamps

meet metal to metal, further tightening of bolts is

not necessary.

Pre-assemble large diameter multi-segment housing

clamps loosely and install them as half-housings.

Take up evenly from top to bottom on alternate bolts.

GROOVED END VALVE CONNECTIONS

WELD END VALVE CONNECTIONS

Clean the end of the pipe and the valve where the

welds will be made. Make up the assembly butting the

connections together. All products have a flow direction

arrow. Make sure it is facing in the direction of the flow.

Tack weld the assembly together and observe the fit.

Warning: If the valve contains a butterfly valve do

not finish welding the assembly with the butterfly

valve installed between the flanges. This will result

in serious damage to the valve seat.

Form # IOM-03.14

Tunstall Corporation

118 Exchange Street

Chicopee, MA 01013

146

Содержание Macon AB Series




























































































































































Результаты поиска

Содержание Macon AB Series

Отзывы:

Tunstall Macon AB Series, Руководство пользователя, Страница: 146 / 155

Результаты поиска

Содержание Macon AB Series

Отзывы: