background image

D O   N OT   D I S C A R D   T H I S   M A N UA L  

T U F F S T U F F   W A R R A N T Y  

TuffStuff warrants to the original purchaser that TuffStuff equipment will be free from defects in material and 
workmanship. All warranty periods begin to run from the date of delivery to the original purchaser. The warranty 
and remedies set forth herein are conditioned upon proper storage, installation, use and maintenance and confor-
mance with any recommendations of TuffStuff. This warranty does not cover products not manufactured by 
TuffStuff or products which are altered without the express written consent of TuffStuff. This warranty as speci-
fied:   

FULL COMMERCIAL WARRANTY

 (more than 5 hours of use per day):  a)  Frames, welds, cams and 

weight plates -- Lifetime,  b) Pivot bearings, pulleys, bushings, gas shocks and guide rods -- Five (5) years,  c) 
Belts, linear bearings and pull-pin components -- One (1) year, and  d) Upholstery, cables, finish and rubber grips 
-- Six (6) months.   

LIGHT COMMERCIAL WARRANTY

 (less than 5 hours of use per day):  a) Frames, welds, cams and weight 

plates -- Lifetime,  b) Pivot bearings, pulleys, bushings, gas shocks and guide rods -- Five (5) years,  c) Linear 
bearings, finish and pull-pin components -- One (1) year, and  d) Upholstery, cables and rubber grips --  Three 
(3) months, and all other parts not mentioned elsewhere in this warranty will expire one (1) year from the date of 
delivery to the original purchaser. The obligation of TuffStuff under this warranty is limited to repairing or re-
placing warranted defective parts, as TuffStuff may elect, at TuffStuff’s facility in Pomona, California, without 
charge to purchaser for either parts or labor. Purchaser is responsible for installation of repaired or replaced parts, 
and all transportation and insurance costs on returned or replaced equipment to and from TuffStuff’s facility in 
Pomona. 

 

THE FOREGOING SHALL CONSTITUTE THE SOLE REMEDY OF THE PURCHASER AND THE 
SOLE LIABILITY OF TUFFSTUFF WITH REGARD TO WARRANTY. NO IMPLIED STATUTORY 
WARRANTY OR IMPLIED STATUTORY WARRANTY OF MERCHANTABILITY OR FITNESS 
FOR A PARTICULAR PURPOSE SHALL APPLY. IN NO EVENT, WHETHER AS A RESULT OF 
BREACH OF CONTRACT, WARRANTY, NEGLIGENCE OR OTHERWISE, SHALL TUFFSTUFF BE 
LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING, BUT NOT 
LIMITED TO, LOSS OF PROFITS OR REVENUE, LOSS OF USE OF EQUIPMENT, COST OF CAPI-
TAL, COST OF SUBSTITUTION EQUIPMENT, DOWNTIME COST, OR CLAIMS OF CUSTOMERS 
OR PURCHASER FROM SUCH DAMAGE. 

 

This written warranty is the final, complete and exclusive agreement of the parties with respect to the quality or 
performance of the equipment and no action for breach of this written warranty or any implied warranty shall be 
commenced more than one (1) year after the accrual of the cause of action. No modification of this warranty or 
waiver of its terms shall be binding on either party unless approved in writing by an authorized representative of 
the party. Contact TuffStuff Fitness Equipment, Inc. at 1325 E. Franklin Avenue, Pomona, California 91766, 
before returning any defective equipment. 

TuffStuff Fitness Equipment, Inc.

 

1325 E. Franklin Avenue  

Pomona, CA 91766, USA 

Ph: 909-629-1600  Fax: 909-629-4967 

E-mail: [email protected]   Net: www.tuffstuff.net 

Содержание Apollo Deluxe









Отзывы: