Tuff stuff MSL-IV Скачать руководство пользователя страница 6

Страница: 6 / 24

FIG. 13

Secure the two

Pec Dec Cams (#9)

to the

Pec

Dec Housing (#18)

using two

Retaining Snap Rings (#49)

. If

possible, use special snap ring pliers for this job, as shown
above. If not available, carefully work each

Retaining Snap

Ring (#49)

into the groove, then push down alternately with a

screw driver working the

Retaining Snap Ring (#49)

into the

groove.

Note

: Be careful not to distort the

Retaining Snap

Ring (#49)

or bend it.

FIG. 14

Insert a

Handle Bracket Left (#11)

and

Right

(#97)

into the two

Pec Dec Arms (#7)

and secure them using

two Hex Head Cap Screws 3/8 -16 X 1 (#81) and two Fender
Washers 3/8- 1 1/2 (#106).

FIG. 15

Insert the two

Pec Dec Swivel Pulley Brackets

(#25)

into the receptacles on the

Top Pulley Assembly (#5)

and secure using four Flat Washers SAE 1/2 (#89) and two
Nylon Insert Lock Nuts 1/2-13 (#88). Do not over-tighten these
nuts, as the

Pec Dec Swivel Pulley Brackets (#25)

must

move freely during use of the machine.

Note

: It is

recommended that the

Pec Dec Swivel Pulley Brackets (#25)

be greased prior to assembly.

FIG. 16

Install the

Ab Crunch Insert Bracket (#57)

and

one Nylon Pulley 4 1/2 Rd. (#35-Not shown See Fig 56) into
the

Rear Upright (#4)

and secure it using one Hex Head Cap

Screw 3/8-16 X 2 1/2 (#78), two Flat Washers SAE 3/8 (#90)
and one Nylon Insert Jam Lock Nut 3/8-16 (#86).

MSL-IV Muscle IV Home Gym

Содержание MSL-IV

























Результаты поиска

Содержание MSL-IV

Отзывы:

Похожие инструкции для MSL-IV

Бренды по названию

Популярные бренды

Tuff stuff MSL-IV, Руководство по сборке и инструкция

Результаты поиска

Содержание MSL-IV

Отзывы:

Похожие инструкции для MSL-IV

Бренды по названию

Популярные бренды