TTGO TGW, Инструкция по установке и эксплуатации

Страница: 10 / 72

5
– English
EN
• Since the sensor’s body is jointed and can be oriented as desired, ti can also be in-
stalled to sloping surfaces. The tilt range is given in the Quick reference guide (Step 1
- Fig. B - phase 1 ).
• Ensure that the surfaces selected for installation are solid and guarantee a stable fixture.
• Make sure that the sensor is protected against accidental impact.
PRODUCT INSTALLATION
3
For installation, fix the various parts of the product in numerical order as shown in the
Quick reference guide (Step1 -
Fig. C
). Then adjust the sensor body as shown in the
Quick reference guide (Step 1 -
Fig. B
- phase
1
).
Make sure that the wind sensor blades are horizontal (Quick reference guide - Step 1 -
Fig. D
).
ACTIVATION AND MEMORISATION
OF THE SENSOR IN THE MOTOR
RECEIVER
4
CAUTION! - Prior to proceeding with any memorisation activity, first
activate the sensor (Quick guide - Step 2):
01.
Turn the two trimmers “
Sun
” and “
Wind
” anti-clockwise to position “
30
”.
02.
Press and hold the “
P1
” button for 4 seconds: the green LED “
L1
” will flash 6 times.
Important! This procedure must only be performed once as an initial
activation.
As for any other transmitter, the climatic sensor’s radio code must be memorized in the
receiver of the motor it controls, so that the sensor can send wireless commands.
To memorise the sensor follow the “Mode I” procedure described in the manual of the
tubular motor or associated receiver. Alternatively the following memorisation procedure
can be used.
• Procedure for memorising the sensor using an already memorised
transmitter
Caution:
This procedure (Quick reference guide - Step
3
) may only be used if one or more radio
codes have already been memorized in the tubular motor.
01. Caution!
– Make sure that the “
Sun
”
(TGWS only)
and “
Wind
” trimmers are
not set to “
Test
”. Turn them to another value if necessary.
02.
Hold down for 10 seconds button “
P1
” of the new sensor and then release it.
03. Press the button of a previously memorized transmitter 3 times (slowly).
04.
Press the again the button “
P1
” of the sensor to be memorized for at least 2 sec-
onds and check that the motor emits 3 signals(*) (= memorization successful).
Note
– If the memory is full, the motor emits 6 signals(*), notifying the user that
memorisation of the new sensor is not possible.
(*)
Note
– The signals correspond to small movements.
• Checking that the sensor has been memorized
01.
Shut off electrical power to the motor; wait for 2 seconds and restore power.
02.
Send a command to the system and, while it is executing, press sensor button P1 for
at least 2 seconds. Now, check that the motor immediately stops (= sensor memorized).
CALIBRATING THE SENSORS
5
Once the sensors have been memorized, they must be calibrated, as follows.
Note to the procedures
– When the trimmer is set to “Test”, the system sets the sen-
sor threshold to a minimum, so that it can react to events without the delays employed
in normal operation. This serves to quickly check that the system is behaving properly.
•
Calibrating the sun sensor (TGWS only - not available on TGW)
(Quick reference guide - Step 4 )
01.
Illuminate the sun sensor with bright sunlight; if the day is very cloudy, use a lamp.
The brightness of the light striking the sensor must be at least 1Klux.
02.
Turn the “
Sun
” trimmer CCW to “
Test
”.
03. Check that the motor lowers the awning and the green Led flashes briefly several
times (= threshold exceeded).
04.
Now obscure the sun sensor with a hand or a black cloth which lets no light
through, and after 15 seconds or so, check:
a) the Led must flash alternately red and green alternately briefly several times (=
return to within threshold); b) the sensor must tell the motor to raise the awning.