Tsurumi Pump LH Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 22

background image

-16-

Exploded View [ LH4110W ]

Reassembly

Reassembly can be performed by reversing the steps for disassembly.

Assemble the three pump casings (uppper, middle, and lower casings) in such a manner that each rib
provided on the periphery of these three casings matches each other in a straight line.

If they are not properly aligned, pumping will not be possible..

After reassembling the pump, be sure to f ll it with the required amount of oil. Replace the packing and o-ring
with new parts. Replace any other worn or damaged parts as well.

The sliding surface of the mechanical seal should be wiped clean with a non-oily cloth. For ease of insertion,

oil the outer parts of the shock-absorbent rubber.

See the manual that comes with the replacement mechanical seal for further derails.

After attaching the impeller, and again after assembly is completed, check to make sure the impeller rotates

smoothly and that is does not rub against the pump casing.

The mouth rings are press-f t into the upper pump casing and the lower pump casing, and the labyrinth
rings are press-f t into the upper pump casing and the middle pump casing; so it is necessary to replace the
related pump casing(s) together when worn.

Note:

Note:

Note:

Note:

Oil Lifter

Round Head

Screw

Mechanical

Seal

Oil Casing

Upper Pump

Casing

Middle Pump

Casing

Lower

Pump

Casing

Packing

O-Ring

O-Ring

O-Ring

O-Ring

O-Ring

O-Ring

O-Ring

Oil Plug

Key

Grease Plug

Impeller Adjusting

Washer

Impeller Adjusting

Washer

Upper Impeller

Lower Impeller

Hex.Nut

Impeller.Nut

Plain Washer

Plain Washer

Upper Shaft

Sleeve

Middle Shaft

Sleeve

Lower Shaft

Sleeve

Hex.Bolt

Hex.Soket Bolt

Hex.Nut

Hex.Nut

Hex.Bolt

Hex.Nut

Hex.Nut

Spring Washer

Spring Washer

Spring Washer

Hex.Bolt

Hex.Nut

Spring Washer

Spring Washer

Stud Bolt

Stud Bolt

Stud Bolt

Stud Bolt

Packing

Packing

Upper Labyrinth

Ring

Lower Labyrinth

Ring

Mouth Ring

Mouth Ring

Strainer

Stand

Cathodic

Protection

Plate

«
...
15
16
17
18
19
...
»

Содержание LH Series























Отзывы:

Нет отзывов

Похожие инструкции для LH Series

Бренд: YANGTECH Страницы: 16

TURBOPOWER 1000 P 225A-TPL

Бренд: PVI Industries Страницы: 1

Бренд: PAPILLON Страницы: 16

Alwayzaire P3062

Бренд: Bestway Страницы: 2

Бренд: Gianneschi Страницы: 28

Бренд: Eagle Pro Страницы: 50

LARIUS VEGA 5:1

Бренд: Samoa Страницы: 28

Бренд: Seisco Страницы: 20

BioPressure II 6000

Бренд: ubbink Страницы: 64

Бренд: Wacker Neuson Страницы: 52

Бренд: baracuda Страницы: 14

Little Giant 16 G Series

Бренд: Franklin Electric Страницы: 36

Бренд: KIRLOSKAR Страницы: 11

SUF-130- 300/400/500

Бренд: State Water Heaters Страницы: 76

Бренд: Penguin Страницы: 10

Бренд: Balboa Страницы: 7

Бренд: P.I.T. Страницы: 18

GRACO TORPEDO G1275-2P100

Бренд: QED Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды