Tsurumi Pump 100C222 Скачать руководство пользователя страница 17

Страница: 17 / 19

-16-

Storage

If the pump will not be operated for a long period of time, pull the pump up, wash the pump, allow it to dry,

and store it indoors.

For reinstallation, be sure to perform a trial operation before putting the pump into operation.

If the pump remains immersed in water, operate it on a regular basis (i.e. once a week).

Note:

Oil Inspection and Changing Procedures

Inspecting Oil

Remove the oil plug and take out a small amount of oil.

The oil can be extracted easily by tilting the pump so that

the oil filler plug faces downward. If the oil appears milky

or intermixed with water, a likely cause is a defective shaft

sealing device (i.e. mechanical seal), which requires that

the pump be disassembled and repaired.

Changing Oil

Remove the oil plug and drain the oil completely. Pour a

specified volume of oil into the oil filler inlet.

The drained oil must be disposed of properly to prevent it

from being released into the sewer or rivers. The packing or
the O-ring for the oil plug must be replaced with a new part
at each oil inspection and change.

Note:

Oil Inlet

Packing

Oil Plug

Hex Key Wrench

Model with 1.5kW power output

Model with 2.2 ~ 3.7kW power output

Model with 0.75kW power output

900

440

Applicable Model

Specified

Volume

Model with 5.5 ~ 11kW power output 2,240

1,890

Model with 15kW power output

Model with 22kW power output

3,400

3,300

Specified Oil: Turbine Oil VG32 (non-additive)

Motor, 2-Pole

Model with 0.75kW power output

Model with 0.4kW power output

620

Applicable Model

Specified

Volume

Model with 1.5kW power output

970

Model with 5.5kW power output

Model with 2.2 ~ 3.7kW power output

4,200

1,350

Model with 11kW power output

6,400

Model with 15kW power output

5,500

Model with 7.5kW power output

4,800

Model with 1.5kW power output

for USA specifications

1,150

Motor, 4-Pole

Three-Phase

Model with 0.75kW power output

590

Applicable Model

Specified

Volume

Motor, 2-Pole Single-Phase

Model with 11 ~ 15kW power output

6,000

Applicable Model

Specified

Volume

Motor, 6-Pole Three-Phase

Three-Phase

(1)

(2)

(1) The specified volume of (TOS) 100C45.5-53/63

will be 4,300ml.

(2) The specified volume of (TOS) 100C47.5-53/63

will be 5,200ml.

Содержание 100C222




















Результаты поиска

Содержание 100C222

Отзывы:

Бренды по названию

Популярные бренды

Tsurumi Pump 100C222, Руководство по эксплуатации

Результаты поиска

Содержание 100C222

Отзывы:

Бренды по названию

Популярные бренды