background image

2. Panel Layout

1) Flont Panel(4CH)

① POWER SW

for Power on/off

② LCD indicator

● Scaling Parameter is default value

LCD indicate encoder pulse count.
(the least significant 7 decimal digit)
* if count value is more than +2147483647 or less than -2147483648, 
  the polarity will be reversed

upper :current counter value
lower :preset value(can be changed by ⑤ and ⑥)

when SETUP mode, display setting item

● Scaling Parameter is not default value

LCD indicate scaled value. 
When the most significant 7 decimal digit does not include a decimal 
point, the most significant 7 digit is displayed.
When the most significant 7 decimal digit include a decimal point,
the most significant 6 digit is displayed.

upper :scaled value
lower :preset value(can be changed by ⑤ and ⑥)

when SETUP mode, display setting item

③ SETUP SW

for SETUP mode

④ Phase Z LED

monitor of Phase Z pulse
(can be turn off by setting)

⑤ Degit

when setting preset value and IP address, change degit.
If you press both (←)button and (→)button for 3 seconds,
scaling parameter is initialized. 

⑥ INC/DEC

increase or decrease preset value and IP address
If you press both INC and DEC for 3 seconds, preset-data turns to zero.

⑦ PRESET

Preset data to each Position Counter
preset enable to maximum ±9999999
when SETUP mode, change setting item

④ ⑤

2

Содержание ER2C-04











Отзывы: