Tsubaki ZIP CHAIN ACTUATOR ZCA25 Скачать руководство пользователя

Страница: 2 / 58

ZIP CHAIN ACTUATOR

Safety Points



Before using this product (installation, operation, maintenance, inspection, etc.) please thoroughly read this

instruction manual and the other attached documents, and operate the product correctly. Familiarize yourself
with the equipment, safety information, and precautions listed herein thoroughly before operation.

After reading, keep this manual in a convenient place for reference.



Safety precautions in this manual are classified into two categories: “Warnings” and “Cautions”.

: Death or serious injury may result from misuse of the product

: Minor or moderate injury, as well as damage to the product, may result from

misuse of the product

Failure to follow the instructions under

Caution

may also result in death or serious injury

depending on the particular situation.

All precautions described below are important and should always be followed.

Warning

Caution

Содержание ZIP CHAIN ACTUATOR ZCA25



























































Результаты поиска

Содержание ZIP CHAIN ACTUATOR ZCA25

Отзывы:

Похожие инструкции для ZIP CHAIN ACTUATOR ZCA25

Бренды по названию

Популярные бренды

Tsubaki ZIP CHAIN ACTUATOR ZCA25, Инструкция по эксплуатации

Результаты поиска

Содержание ZIP CHAIN ACTUATOR ZCA25

Отзывы:

Похожие инструкции для ZIP CHAIN ACTUATOR ZCA25

Бренды по названию

Популярные бренды