TSC TTP-2410M Скачать руководство пользователя страница 46

Страница: 46 / 47

TTP-2410M/346M/644M
TTP-246M Plus/344M Plus

Bar Code Printer Service Manua

UPDATE HISTORY

Date

Content

Editor

2007/12/4

Modify electronics cover part no. from 32-0240004-00LF to

98-0240031-00LF.

Camille

2007/12/5

Add internal rewinding kit part no. (Option).

Camille

2008/1/24

Revise description for 98-1000011-00LF External wireless

print server (C)/ US & 98-1000012-00LF External wireless

print server (C)/ EU

Camille

2008/2/19

Modify the

print head module

part number. (Add screw)

Camille

2008/2/22

Add 2.4 section: Internal Rewinding Kit Installation (Option)

Camille

2008/2/29

Add print head module (TTP-644M) and peel-off sensor ass’y

part number

Camille

2008/3/7

Revise the Maintenance section

Camille

2008/3/12

Revise the Troubleshooting section

Camille

2008/3/21

1.Add print head harness (TTP-644M) part number

2.Update the LCD panel board assembly part no. from -00LF

to -10LF

3.Update the interface plate part no. from -00LF to -10LF

Camille

2008/4/29

1.Update the Multi-interface board part no. from -01LF to

-11LF

Camille

2008/6/23

1.Remove the part list section

Camille

2008/10/3

Revise the 3.9 section

Camille

2008/11/20

Revise the 3.7 section (Replacing the stepping motor)

Camille

2009/3/16

Modify section 1.1 (Recommended SD card specification)

Camille

2009/4/15

Revise section 3.13 & 3.14 (Peel-off kit installation & Internal

rewinding kit installation)

Camille

2009/9/25

Revise section 2.1

Camille

2010/8/13

Revise section 3.8

Camille

2010/11/5

Revise section 3.13

Camille

Содержание TTP-2410M
















































Результаты поиска

Содержание TTP-2410M

Отзывы:

Похожие инструкции для TTP-2410M

Бренды по названию

Популярные бренды

TSC TTP-2410M, Руководство по обслуживанию

Результаты поиска

Содержание TTP-2410M

Отзывы:

Похожие инструкции для TTP-2410M

Бренды по названию

Популярные бренды