TSC TTP-2410M Скачать руководство пользователя страница 40

Страница: 40 / 47

TTP-2410M/346M/644M
TTP-246M Plus/344M Plus

Bar Code Printer Service Manua

Ribbon encoder

sensor doesn’t work.

* The ribbon encoder sensor connector

is loose.

* Fasten the connector.

Ribbon end sensor

doesn’t work.

* The connector is loose.
* The ribbon sensor hole is covered with

dust.

* Check the connector.
* Clear the dust in the sensor hole by the blower.

Peel sensor is not

working.

* Peel sensor is not located on the

correct position.

* The connector is loose.

* Make sure that the media goes through the Peel

sensor.

* Plug the connect cable correctly.

Cutter is not working.

* The connector is loose.

* Plug in the connect cable correctly.

Label feeding is not

stable (skew) when

printing.

* The media guide does not touch the

edge of the media.

* If the label is moving to the right side, please

move the label guide to left.

* If the label is moving to the left side, please

move the label guide to right.

Skip labels when

printing.

* Label size is not specified properly.
* Sensor sensitivity is not set properly.
* The media sensor is covered with dust.

* Check if label size is setup correctly.
* Calibrate the sensor by Auto Gap or Manual

Gap options.

* Clear the GAP/Black mark sensor by blower.

The printing position

of small label is

incorrect.

* Media sensor sensitivity is not set

properly.

* Label size is incorrect.
* The parameter Shift Y in the LCD menu

is incorrect.

* The vertical offset setting in the driver is

incorrect.

* Calibrate the sensor sensitivity again.
* Set the correct label size and gap size.
* Press [MENU]

[SELECT] x3

[DOWN]x6

[SELECT] to fine tune the parameter of Shift Y.

* If using the software BarTender, please set the

vertical offset in the driver.

The left side printout

position is incorrect.

* Wrong label size setup.
* The parameter Shift X in LCD menu is

incorrect.

* Set the correct label size.
* Press [MENU]

[SELECT] x 3

[DOWN] x 5

[SELECT] to fine tune the parameter of Shift

Missing printing on

the left or right side of

label.

* Wrong label size setup.

* Set the correct label size.

Содержание TTP-2410M
















































Результаты поиска

Содержание TTP-2410M

Отзывы:

Похожие инструкции для TTP-2410M

Бренды по названию

Популярные бренды

TSC TTP-2410M, Руководство по обслуживанию

Результаты поиска

Содержание TTP-2410M

Отзывы:

Похожие инструкции для TTP-2410M

Бренды по названию

Популярные бренды