TSC TTP-2410M Скачать руководство пользователя страница 2

Страница: 2 / 47

TTP-2410M/346M/644M
TTP-246M Plus/344M Plus

Bar Code Printer Service Manua

TABLE OF CONTENT

1. FUNDAMENTAL OF THE SYSTEM .......................................................................... 1

1.1. Overview.................................................................................................................1

2. ELECTRONICS.......................................................................................................... 5

2.1 Summary of Board Connectors.............................................................................5

2.2 Interface Pin Configuration..................................................................................10

3. MECHANISM ........................................................................................................... 13

3.1 Remove Covers and the Lower Front Panel.......................................................13

3.2 Replacing the LCD Panel Module ........................................................................15

3.3 Replacing the Power Supply Unit........................................................................16

3.4 Replacing Multi-interface Board ..........................................................................17

3.5 Replacing the Main Board....................................................................................18

3.6 Replacing the Platen Roller Assembly................................................................19

3.7 Replacing the Stepping Motor .............................................................................20

3.8 Replacing the Print head ASS'Y ..........................................................................21

3.9 Replacing the Gap/Black Mark Sensor Module..................................................23

3.10 Replacing the Media Damper.............................................................................24

3.11 Replacing the Ribbon Rewind Spindle..............................................................25

3.12 Cutter Module Installation (Option) ...................................................................26

3.13 Peel-off Kit Installation (Option) ........................................................................27

3.14 Internal Rewinding Kit Installation (Option) .....................................................31

4. TROUBLESHOOTING............................................................................................. 35

4.1 Common Problems ...............................................................................................35

4.2 Mechanism Fine Adjustment to Avoid Ribbon Wrinkles ...................................40

5. MAINTENANCE....................................................................................................... 42

UPDATE HISTORY ...................................................................................................... 44

Содержание TTP-2410M
















































Результаты поиска

Содержание TTP-2410M

Отзывы:

Похожие инструкции для TTP-2410M

Бренды по названию

Популярные бренды

TSC TTP-2410M, Руководство по обслуживанию

Результаты поиска

Содержание TTP-2410M

Отзывы:

Похожие инструкции для TTP-2410M

Бренды по названию

Популярные бренды