TSC DA210 Series Скачать руководство пользователя | Manualshive

Страница: 27 / 44

background image

DA210/ DA310/ DA220/ DA320
Bar Code Printer Service Manual

26

11. Lift up both latches of gap sensor cover into the printer inner cover. (you can press

the center of the printhead module for installing the cover easily) Please note that

the gap sensor cover CANNOT press the printhead module.

The gap sensor cover should cover about 1/2 printhead.

12. Press back the gap sensor cover tabs into the socket.

Latch

Press

O

X

«
...
25
26
27
28
29
...
»

Содержание DA210 Series













































Отзывы:

Нет отзывов

Похожие инструкции для DA210 Series

Бренд: Icarus Страницы: 35

Бренд: Component Engineering Страницы: 11

Бренд: Winkhaus Страницы: 5

Бренд: Cognex Страницы: 29

SecOVID Reader III

Бренд: Kobil Страницы: 20

Бренд: Infinite Peripherals Страницы: 19

Бренд: Panasonic Страницы: 98

FZ-VSC402 Series

Бренд: Panasonic Страницы: 8

FZ-VSC401 Series

Бренд: Panasonic Страницы: 8

Бренд: Argox Страницы: 34

Бренд: IDTECH Страницы: 98

Бренд: Gemplus Страницы: 36

Бренд: Allflex Страницы: 5

Бренд: Unitech Страницы: 2

Бренд: ZKTeco Страницы: 6

Бренд: IDTECK Страницы: 12

Бренд: RaidSonic Страницы: 2

Бренд: Leuze electronic Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды