Tryton TMS23020, Руководство по эксплуатации

Страница: 9 / 56

8
n
Rough grinding humidity, dust penetration and small objects; remember to protect its
ventilation openings. Small objects after getting into the casing can
For best rough grinding efficiency the angle between the disk and
result in damage to the motor.
º º
machined surface should range from approx. 30 do 40 (see: Fig.J, p.2).
The tool should be slightly pressed against the surface and smoothly
MANUFACTURER:
moved along the material. Thanks to the right pressure the machined
PROFIX Ltd. ;
part does not heat up excessively, does not lose its color and no grooves
34 Marywilska Street,
or other roughness will appear on its surface.
3-228 Warsaw, POLAND
NOTE: Never use cutting disks to grind/remove layers.
ENVIRONMENTAL PROTECTION :
n
Cutting
NOTE : The symbol nearby denotes that old equipment must
While cutting with the tool do not exert excessive pressure, do not tilt
never be disposed together with other wastes (with the and do not oscillate. Move the tool at a constant speed adjusted to the
penalty of a fine). Hazardous components of electronic
material machined.
equipment may adversely affect the natural environment and
Do not brake the rotating disk by pressing it against other objects.
human health.
NOTE: Observe proper cutting direction. Cutting should be carried out at
Each household may contribute to recovery and reuse (recycling) of old
the direction shown on the disk (see: Fig. K , p.2). Do not cut in opposite
machinery and equipment. Both in Poland and Europe a system for
direction! Otherwise the tool may be pulled out from the cutting line.
recovery of used equipment either exists or is being developed. The
system obliges all organizations that sell such equipment to collect back
The tool does not require any special maintenance. Store it away from
the used machinery and appliances. Moreover, general purpose
children, keep clean and protect against humidity and dust. Storage
collecting points for such equipment are also available .
conditions should exclude any mechanical damage or harmful weather
factors.
This device meets the requirements of national and European standards
and safety guidelines. Any repair can be carried out only by qualified
personnel using original spare parts.
n
Cleaning
To provide safe and efficient operation, the grinder casing and venti -
lation openings should be free from dust deposits and other pollutants.
We recommend that you clean the grinder directly after each use.
Wipe the grinder with a clean, slightly wet cloth with a small amount of
soap. Do not use any cleaning agents or solvents; they can damage parts
made of plastics. Protect the grinder's inner parts against water.
After using the tool in dusty atmosphere it is recommended to clean the
ventilation openings with compressed air to avoid damage to the
bearings and remove dust blocking the air used for cooling the motor.
- check whether the power cord ( 7 ) is correctly plugged in and the
electric power outlet is energized;
- check condition of carbon brushes and replace them if necessary.
- if the defect persists, the tool fails to work despite of voltage presence
and carbon brushes are in good condition, hand the tool over for repair
to an authorized workshop to the address specified in
.
Store and transport the grinder in its transport box to protect it against
STORAGE AND MAINTENANCE:
TROUBLESHOOTING:
The electric tool fails to switch on or works with breaks:
TRANSPORT:
NOTE! Carbon brushes can be replaced only by competent electricians.
w arranty card
PICTOGRAMS:
Explanation of the icons located on the nominal plate and the
information tags
.
«WARNING! Read this instruction before switching
on the power supply and starting the work»
«Always wear safety goggles»
«Wear » hearing protection
«Wear protective gloves »
«Wear a dust mask»
The policy of the PROFIX company consists in permanent improvements of the offered products and therefore the company
reserves the right to make amendments to the product specification without a prior notice. The images included into the
operation manual are only of the exemplary nature and may slightly differ from actual appearance of the device
purchased.
This
instruction manual is protected by copyright. Copying it without the written consent of PROFIX Co. Ltd. is prohibited.