Tryton TMS125RK, Руководство по эксплуатации

Страница: 8 / 60

8
The vibration level value given refers to basic application of the tool. If the
tool is used for other applications or with other tools, or if it is not
maintained properly, the vibration level may differ from the values given.
The above-mentioned causes may lead to higher exposure to vibrations
during the whole work time.
One must implement additional safety measures to protect the operators
from exposure to vibrations, such as maintenance of the electric tool and
work tools, assurance of proper hand temperature, or determination of
the sequence of work operations.
ź
To switch the tool on it is first necessary to depress the unlocking
button ( 9 ) and then depress the On/Off ( 10 ) and hold it
depressed.
ź
To switch the tool off it is enough to release the On/Off ( 10 ).
NOTE: Due to safety reasons the On/Off ( 10 ) cannot be locked for
continuous operation. It must be kept depressed manually by the operator
during the entire time of the tool operation.
n
Grinding angle
Do not use the whole disk surface to grind, use its edge only.
For efficient grinding the angle between the disk and machined part
º º
should range from approx. 15 to 30 (see: Fig. , p. 3 ).
n
Rough grinding
For best rough grinding efficiency the angle between the disk and
º º
machined surface should range from approx. 30 do 40 (see: Fig. H , p. 3 ).
The tool should be slightly pressed against the surface and smoothly
moved along the material. Thanks to the right pressure the machined
part does not heat up excessively, does not lose its color and no grooves
or other roughness will appear on its surface.
avoiding damage to the motoreducer casing during the disk
removal.
NOTE: The spindle lock button ( 6 ) can be pressed only when the spindle is
stopped! Never use a disk with improper maximum admissible speed!
n
Trial start up
After inserting a disk and after connecting the grinder to the mains check
whether the disk is properly fixed and whether it rotates without any
obstacles.
The initial/trial start up should be carried our away from people.
BEFORE YOU START WORKING:
1. Make sure that the power source parameters match the parameters
presented on the grinder nameplate.
2. Make sure that the grinder power switch ( 10 ) is in off position.
3. When using an extension cable make sure the extension cable
parameters and conductor sections match the grinder parameters. It
REGULAR OPERATION:
is recommended to use the shortest extension cables possible. The
n
Switching on/off
extension cable should be fully unwound.
Before you switch on the tool check if the switch ( 10 ) is in working order
n
Mounting the side handle
and returns to “Off” position after releasing.
NOTE: For safety reasons always use the side handle ( 1 ).
Depending on the operating requirements screw the side handle to the
switch
end in one of th re e seats provided in the grinder head (see: Fig. B , p. 2 ).
n
Mounting the disk guard switch
NOTE: Before you install or remove the disk guard, make sure that the switch
device switch is in off position and that it is disconnected from the mains.
To cut or grind with grinding or cutting disks it is necessary to install the
disk guard (
2 ). Adjust the guard position to the operation performed.
n
Setting the speed
The closed side of the guard should be always directed towards the
Using rotational speed control ( 7 ) the user can set a desired speed. It can
operator. To install the disk guard:
be done during operation.
ź
Place the grinder with the spindle ( 1 2 ) up.
Speed depends on the material drilled and working conditions and can
ź
Install the blade guard as shown in Figure C , page 2 .
be determined by performing a test.
ź
Match holes on the guard flange ( 1 1 ) with mounting holes in
n
Tips regarding the operation
grinder's head and insert fixing screws into the flange. Tighten
ź
The objects to be machined that do not rest securely under their own
securely the screws using a Phillips type screwdriver (Ph2).
weight should be fixed properly.
n
Grinding tools assembly (see: Fig. D , E , F p. 3 )
ź
Avoid excessive pressure exerted on the disk. Grinding should be
NOTE: Before you install or remove the grinding disk, make sure that the
carried out using the weight of the tool. Only slight pressure is allowed
device switch is in off position and that it is disconnected from the mains.
when cutting. Excessive pressure reduces the disk speed, which results
Before installation clean the grinder spindle and all fixing components.
in producing rough surfaces. In addition, it results in overheating and
Make sure the admissible size and speed of the grinding disk matches damage to the motor.
the parameters presented on the grinder nameplate. The grinding disk
n
Grinding direction
should be installed without any clearance on the fixing flange. Do not
When using a new grinding disk move the grinder back ( B direction)
use any reduction washers or adapters.
(see: Fig. G , p. 3 ), then the new disk edge will be rounded, which will
To install a disk:
allow the user to move the tool in any direction.
1. Place the grinder with the spindle ( 1 2 ) up. Insert the fixing flange
( 4 ) with its bottom projecting part with a groove onto the spindle
shaft to mesh the flange on the spindle.
2. Insert a disk ( 1 3 ) with its convex part down onto the upper
G
projecting part of the fixing flange.
3. Screw the compression nut ( 3 ) onto the spindle to secure the disk
properly. (The compression nut has a concave and convex side.
Depending on the rated disk thickness it can be applied on one or
the other side. (see: Fig.
E p. 3 ).
4. Press the spindle lock button ( 6 ) and tighten the nut using the pin
wrench ( 1 4 ) exerting a slight force as the nut automatically tightens
up during operation. Observing this recommendation will help
3 minutes or more
1 minute or more
Trial operation
period After disk
replacement
At first start up