Tryton TMR800K, Руководство по эксплуатации

Страница: 7 / 48

parameters of the extension cord and the cross-sections of the cables
ź
To turn the power tool off just release the switch ( 9 ) button or, when it
match the parameters of the jig saw. Use the shortest extension cords
is locked with switch lock ( 8 ), press it for a moment and then release it.
possible. The extension cord used should be completely unfolded.
n
Preliminary selection of the speed
4. When cutting a wood piece that has been processed, watch out for
In the top front part of the jig saw handle there is a speed control knob
foreign objects, such as nails, screws, etc.
( 6 ). The knob can be used to set up the cutting speed, which depends on
NOTE! Remove the plug from the power tool's mains before any
the type of material to be cut and the working conditions, and can be
adjustments, replacement of parts or storage of the device.
selected by trial and error.
n
Installing the blade After long work with low speed, cool down the motor by switching it off
and making it work without load with maximum speed for approx. 3
The jig saw can work with any blades with T-type (type A acc. to Profix
minutes.
catalogue). The tools sold by the manufacturers, most often in sets,
depending on their intended use, can have different size and type of the
n
Adjustment of the orbital cutting action
cutting teeth. The manufacturer usually provides information on the
On the left side of the jig saw body there is a switch to control the ancillary
intended use of the different blades on the blade set package or in an
orbital cutting action ( 1 5 ) of the jig saw head (the undercut function).
This additional functionality makes it possible to optimize the work
process for specific materials.
The following four options of the orbital cutting action can be selected
with the switch (
1 5 ) . The options can be changed when the tool is on:
Option 0 – Orbital cutting action off
Option 1 – Small orbit cutting action
Option 2 – Medium orbit cutting action
Option 3 – Large orbit cutting action
It is recommended that:
ź
The orbital cutting action should be the smaller (or off) the finer and
cleaner the cutting edge must be.
ź
When cutting thin materials, such as metal sheet, orbital cutting
action should be off.
ATTENTION! Check if the blade is fixed firmly. Loose blade may fall out and
ź
In the case of hard materials, such as steel, small orbit cutting action
injure the operator.
should be selected.
ź
In order to remove the blade, perform the above-mentioned actions in
ź
In the case of soft materials and for ripping large orbit cutting action
the reverse order.
should be selected.
n
Compartments for blades
ź
When using knife-type blade, orbital cutting action should be
Integrated magnetic compartments for blades ( 11 ) are located on both
off.
sides of the fret saw. They can be used for storing the blades.
The optimum work parameters can only be found by trial and error.
ź
Open the compartment cover ( 11 ), holding the catch at the top of the
When cutting metal, it is recommended to use a proper cooling-
cover and pull it out (Fig. D ).
lubricating agent along the cut line.
ź
Blades are mounted in the compartment by means of a magnetic strip.
n
Protection guard
To take the blade out, press one of its ends and pull out holding its
The protection guard ( 3 ) located on the tool's housing prevents the user
raised part.
from inadvertently touching the blade during work. The guard must not
ź
Close the cover of the blades' compartment ( 11 ).
be removed.
NOTE! Before you start working, make sure that the compartments are
properly locked.
n
Foot plate
The device is equipped with a plastic foot plate ( 16 ) that prevents
scratching of the surface being cut. If the plate is damaged during
operation, replace it with a new one.
USE:
The jig saw is provided with a connector ( 1 2 ) for connecting a vacuum
n
Switching the jig saw on/off cleaner in order to remove all the saw dust and fillings. The vacuum
cleaner must be suitable for the material being cut.
ź
To turn the power tool on press its switch button ( 9 ) and keep it
NOTE! Before connecting the vacuum cleaner, make sure that the power
pressed.
cord of the fret saw is unplugged.
ź
To lock the switch in on position press the lock ( 8 ). The continuous
Insert the connecting element ( 12 ) to a dust removal nozzle and
operation lock button is available on both sides of the fret saw and
connect the vacuum cleaner hose to it.
allows for easy and comfortable operation by both the right and left-
handed users.
NOTE: When extracting chips, the blowout on/off switch ( 14 ) should be set
n
Sawdust Blower Device
With the air jet of the sawdust blower device, the cutting line can be kept
free of dust and chips.
ź
Switching on the sawdust blower device: set the switch ( 14 ) to on .
ź
Switching off the sawdust blower device: set the switch ( 14 ) to off .
ź
attached leaflet. The individual blades may be marked with different
colors for different materials to be cut.
ATTENTION! Before installing the blade and performing any
maintenance work, make sure that the power cord of the jig
saw is not connected to a power source.
When mounting the saw blade, wear protective gloves. Danger of injury
when touching the saw blade.
A special grip ( 19 ) provides quick installation of the blade.
Pull a grip wheel ( 19 ) towards the arrow (Fig. B ), so that the fastening
groove was parallel to the longitudinal axis of the fret saw.
Insert the selected blade (
20 ), with teeth facing out, all the way into
the grip's slot ( 19 ). Release the grip wheel that automatically locks the
blade (Fig. C ).
ź
ź
n
Sucking out saw dust and fillings (see fig. E )
7