Tryton TMR800K, Руководство по эксплуатации

Страница: 5 / 48

5
e) Power tools require maintenance. Check power tools for particularly dangerous. Light metal dust may become lit up or explode.
concentricity or jamming of moving parts, any cracks and all
e) Secure the workpiece. Make sure that all the clamps are fastened
other factors affecting the power tool work safety. If any
and that there is no excessive clearance. It is safer to fix the workpiece in a
damage to the power tool is detected, it should be repaired holding device or vice than to hold it in your hands.
before use. Improper power tool maintenance is a reason for many
f) Always use protective goggles and hearing protection.
accidents.
Whenever it is necessary use proper personal protective
f) Cutting tools should be sharp and clean. Keeping sharp cutting equipment:
edges in good condition reduces the risk of jamming and facilitates - a face mask to reduce the risk of inhaling harmful dusts;
operation.
- protective gloves when the blade is moving and a rough material is
being handled.
g) Power tools, equipment, working tools etc. should be used
according to this user's manual taking into account operating
g) Make sure that the adjustable foot (1) is properly secured
conditions and the work to be done. Misusing a power tool can during the cutting process. A blocked blade can break or cause
result in dangerous situations.
kickback.
h) At low temperatures and after a long brakes in operation it is h) Use only blades that are in an impeccable condition. Bent or dull
blades can break or cause a kickback. recommended to turn the power tool to operate it with no
load for a few minutes to provide proper grease distribution
i) Start the tool before the blade touches the material. Otherwise,
inside its driving mechanism. there is a risk of kickback when the tool blocks in the workpiece.
i) Use soft, damp (cannot be wet) cloth and soap to clean power j) Hold your hands away from the cutting range. Do not place
tools. Do not use petrol, solvents and other agents that may your hands under the workpiece. You may suffer cuts when
touching the blade.
damage your equipment .
k) After the work is completed, switch off the tool. The blade may
j) Power tools can be stored/carried after making sure that all
be taken out of the workpiece after its motions stop. This way,
moving components are locked and protected against release
kickback can be avoided and the tool can be safely put away.
with original devices intended for this purpose.
l) Disconnect the tool from the power supply during breaks,
k) Store power tools in a dry, dust and water-protected place.
when replacing the blade, and when repairing, cleaning, or
l) Carry your power tool in its original packaging to provide
adjusting the tool.
protection against mechanical damage.
m) Never use a tool with damaged cord. Do not touch a damaged
cord; if the cord becomes damaged during work, take out the
plug from the power socket.
Damaged cords increase the risk of
electric shock.
WARNING! General warnings regarding the use of
ATTENTION! If a permanently fixed power cord becomes damaged, it
power tools.
must be replaced with a special cable or assembly available at the
Repair :
manufacturer's or at a specialized repair service point.
DESIGN AND PURPOSE OF THE JIG SAW:
The jig saw is a tool with second protection class (double insulation), is
supplied with a single-phase engine, and is provided with an electric
speed control system. The possibility to control the speed and the 4-step
a) When performing works where the tool could hit concealed
adjustment of the blade movement guarantee optimum efficiency of the
electric wires or the tool's own cord, the electric tool must be
cutting process.
held by the insulated surfaces of the handle. Contact with a
mains cable may transfer could make the metal parts of the tool live and The jigsaw is intended for cutting in wood and wood-based materials,
result in an electric shock of the operator.
plastics, metal, ceramic tiles, and rubber. The cutting process is effected
with a proper blade which is suitable for the material being cut.
b) Use proper devices to locate concealed power supply cables or
o
ask the building's administrator. Contact with live wires may cause The tool is suitable for straight and inclined cuts, up to 45 . It is intended
a fire and electric shock. Damage to a gas pipe may cause an explosion.
for home and industrial use with medium intensity. It is not suitable for
Damage to a water supply pipe may cause damage to property. long use in hard conditions.
c) Do not work with materials containing asbestos. Asbestos is a
The tool must not be used for work requiring a professional tool.
recognized carcinogenic substance.
Any use of the jig saw that is not in observance with the above-mentioned
d) The work place must be tidy at all times. Mixtures of materials are purpose is forbidden, leads to the loss of warranty, and
m) Keep handles and grip surfaces clean and free from oil and
grease. Secure grip and control over the tool in unexpected
circumstances are impossible if handles and grip surfaces are slippery.
n) jig
EN60825-1:2007
WARNING!
JIG SAW , Additional Safety Warnings:
a)
The saw is provided with a laser pointer, with class
Warranty and post-warranty repairs of its power tools are
2 laser according to the standard.
carried out by PROFIX Service, which guarantees the best
Never look at the laser beam and point the beam at
quality or repair and use of genuine spare parts.
people's or animals' eyes. Looking at a beam emitted by a class 2 laser is
WARNING!
not hazardous, provided that it lasts no more than 0 , 25 s. The eye closing
While operating power tools it is necessary to observe basic
reflex is generally a sufficient protection. Use of optical devices, such as
work safety rules to avoid fire, electric shock or mechanical
glasses or binoculars does not increase the risk of eye injury.
injury.