Tryton TMR800K, Руководство по эксплуатации

Страница: 8 / 48

8
to off position.
n
Rip cut (see fig. F )
Loosen the clamping screws ( 2 ) and slide the parallel guide ( 18 ) through
the holders in the foot ( 1 ). Set the required width with the scale on the
interior side of the guide. Fasten the fixing screws and make the cut.
STORAGE AND MAINTENANCE:
The tool must be stored in a place that is not accessible to children and
must be kept clean and protected from moisture and dust. The storage
conditions should prevent potential mechanical damage and impact of
the weather conditions.
The jig saw in principle does not require any special maintenance or
service. However, by periodically lubricating the blade guide roll (
1 7 ) you
can extend its service life.
Regularly check the condition of the screws fastening the fret saw body
and the foot. If necessary, tighten them.
After work is completed, the ventilation openings and the blade holder
should be cleaned with compressed air. This will prevent damage do the
bearings and remove the dust blocking the access of air to cool the
engine.
The body must be cleaned with a clean, moist cloth with small quantity
of soap and then wiped dry. Do not use any detergents or solvents as they
can damage parts made from plastics.
Make sure than no water enters inside the tool.
NOTE! Carbon brushes can be replaced only by competent electricians.
TRANSPORT:
The jig saw must be transported and stored in the transport case which
protects it from moisture, penetration of dust and small objects. In
particular, the ventilation slots of the jig saw must be protected. Small
items that get inside the housing may damage the engine.
NOTE! Make sure that the adjustable foot is properly secured
during the cutting process. A blocked blade can break or cause
kickback.
To reset the fret saw foot ( 1 ) for straight cutting, repeat the procedure
described above, setting the foot at an angle of 0°.
n
L aser pointer
The laser pointer ( 23 ) shows the line of the cut. Mark the required cut line
on the surface of the workpiece and guide the laser line along the marked
line during the cutting operation.
ź
In order to switch the laser pointer on or off, press the ON/OFF button
( 5 ).
Before you start the cutting operation, make sure the line of the cut is
shown properly. The laser pointer may change its position due to
vibrations present during intensive use of the tool.
REMARK: After the cutting operation is completed, remember to switch off
the laser .
Visible dirt in the outlet orifice of the laser beam should be gently
removed with use of sticks with cotton buds soaked with liquids for glass
cleaning.
- check whether the power cord ( 10 ) is correctly plugged in and the
electric power outlet is energized;
- check condition of carbon brushes and replace them if necessary.
- if the defect persists, the tool fails to work despite of voltage presence
and carbon brushes are in good condition, hand the tool over for repair
to an authorized workshop to the address specified in
.
MANUFACTURER:
PROFIX Co. Ltd.
34 , Marywilska St.,
03-228 Warsaw, POLAND
This appliance is in conformity with national and European standards as
well as with general safety guidelines.
Any repairs are allowed to be carried out exclusively by qualified
staff with use of original spare parts.
n
ź
ź
n
ź
ź
n
w arranty card
n
Tips regarding the operation
NOTE!
- excessive pressure on the jig saw may slow down or interrupt the
movement of the blade and slow down or stop the cutting process
;
- when cutting with the jig saw, its foot should rest with its whole
surface on the workpiece;
- prior to cutting openings in hard materials, a hole must be drilled so
as to place the blade in it;
- when cutting lines forming an acute angle or connected with a small-
radius arc, use narrow blades and switch off the orbital cutting action;
- use of the guide facilitates staying on the cut line.
Battery replacement (see Fig. G )
A laser pointer ( 23 ) is powered by two alkaline batteries AG13 1.5V.
Batteries should be replaced when the laser light becomes dim and the
beam is scattered.
Unscrew the fastening screws ( 21 ) to detach the laser cover ( 4 ) from
the fret saw. Pull the laser cover forwards.
Remove old batteries (
22 ) and put the new ones of the AG13 type in
their place. Make sure that the po) and negative (-) poles are
connected properly. Put the laser cover (
4 ) back to its place.
NOTE! Do not dispose used batteries with other waste. Used batteries or
accumulators shall be left at the waste collection points.
Cutting
Using a drill make a 10 mm hole in the material to be cut.
Insert your jigsaw blade into the hole and start cutting.
Adjusting the saw foot for bevel cutting (see Fig. H)
NOTE! Do not use the fret saw with disassembled or untightened foot.
The fret saw foot ( 1 ) is factory set to the middle position (0°) and can be
adjusted for bevel cutting both to the left and right, up to the angle of
45°.
NOTE! Before changing the fret saw's foot setting angle, make
sure that the power cable is unplugged.
1. Pull the locking lever of the fret saw foot ( 13 ) out to unlock the foot.
2. Pull the fret saw foot ( 1 ) to the front.
3. Set the required angle 22.5° or 45°, using the scale ( 24 ).
4. Push the fret saw foot ( 1 ) to the back.
5. Move the locking lever of the fret saw foot ( 13 ) to the back to lock the
fret saw foot ( 1 ).
The basic principles of proper use of the jig saw:
- cut the material with medium pressure, so that the jig saw is not
overloaded;
TROUBLESHOOTING:
The electric tool fails to switch on or works with breaks: