Tryton TMGK500, Руководство по эксплуатации

Страница: 4 / 40

4
e) Power tools require maintenance. Check power tools for
concentricity or jamming of moving parts, any cracks and all
other factors affecting the power tool work safety. If any
damage to the power tool is detected, it should be repaired
before use.
Improper power tool maintenance is a reason for many
accidents.
f) Cutting tools should be sharp and clean. Keeping sharp cutting
edges in good condition reduces the risk of jamming and facilitates
operation.
g) Power tools, equipment, working tools etc. should be used
according to this user's manual taking into account
operating conditions and the work to be done.
Misusing a
power tool can result in dangerous situations.
h) At low temperatures and after a long brakes in operation it is
recommended to turn the power tool to operate it with no
load for a few minutes to provide proper grease distribution
inside its driving mechanism.
i) Use soft, damp (cannot be wet) cloth and soap to clean power
tools. Do not use petrol, solvents and other agents that may
damage your equipment
.
j) Power tools can be stored/carried after making sure that all
moving components are locked and protected against
release with original devices intended for this purpose.
k) Store power tools in a dry, dust and water-protected place.
l) Carry your power tool in its original packaging to provide
protection against mechanical damage.
WARNING! General warnings regarding the use of
power tools.
Repair :
WARNING! ELECTRIC SCREW DRIVER, security warnings
Personal S afety :
a) Always wear ear protectors when operating the driver.
Exposure to noise can cause hearing loss.
b ) During operations when a screw can damage electric wires,
hold the power tool by the insulated part of its handle.
Cutting accessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator an electric
shock.
c ) Use appropriate detectors to determine if utility lines are
hidden in the work area or call the local utility company for
assistance.
Contact with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explosion. Penetrating a water
line causes property damage or may cause an
electric shock.
d ) Protect the object machined. Make sure all clamps are closed and
check for excessive clearance. It is safer to fix the object machined in a
fixing device or a vice than holding it in your hand.
a) Power tools can be repaired by competent persons only who
use original spare parts.
It will provide safe operation for the power
tool.
g ) Never use a tool with damaged cord. Do not touch a
damaged cord; if the cord becomes damaged during work,
take out the plug from the power socket.
Damaged cords
increase the risk of electric shock.
ATTENTION! If a permanently fixed power cord becomes damaged, it
must be replaced with a special cable or assembly available at the
manufacturer's or at a specialized repair service point.
APPLICATIONS AND CONSTRUCTION:
The tool must not be used for work requiring a professional tool.
Any use of the that is not in observance with the above-
mentioned purpose is forbidden, leads to the loss of warranty, and
relieves the manufacturer from responsibility for the resulting damage.
Any modifications of the tool by the user relieve the manufacturer from
responsibility for any damage and injuries to the user and the
surroundings.
Despite using the tool according to its intended application it is
impossible to eliminate certain residual risk factors. Considering the tool
construction the following risks may occur when operating the tool:
- touching the rotating tool bit with a hand or by operator's clothes;
- burns when replacing a tool bit. (The tool bit heats up intensely
during operation, use pliers and protective gloves to replace it);
- screw throw off.
n
The set includes:
ź
Electric skrew driver - 1 piece
ź
Driving depth limiter (stop) - 1 piece
ź
T ransport box - 1 piece
ź
- 1 piece
ź
Warranty card - 1 piece
n
Power tool components (see page 2 ) :
4. Driving depth limiter
Rotation direction selector
Multi-purpose magnetic chuck *
12. ¼" chuck with a hexagonal tip
* These accessories presented in figures or described herein are
optional.
TECHNICAL DATA:
e ) Hold the power tool tightly. During driving and loosening of
screws, short moments of strong movements in reaction to this action
may occur.
f ) Before you put the power tool aside make sure it is
completely stopped.
The bit can jam resulting in losing control over
the power tool.
The electric screw driver is a hand-held power tool driven by a single-
phase commutator-type motor. This is Class II equipment (double
insulation).
The electric driver is designed for driving and removing screws when
installing dry-wall systems (plasterboard walls), soft wood, plastics,
etc.
The combo drill and driver is designed exclusively for DIY applications .
device
O perating instruction
Fig. A 1. Driving bit *
2. Driving limiter sleeve
3 . Depth limiter setting knob
5 . Belt clip
6 .
7 . On/off switch
8 .
9 .
1 0 .
Fig. B
Switch lock
Handle
Power cord
11.
Rated voltage 230 V
Rated frequency 50 Hz
Power consumption 50 0 W
No load speed 0-1600 rpm