Tryton TJE100, Инструкция по эксплуатации

Страница: 11 / 80

11
PREPARATION FOR WORK:
The blower is delivered in the packaging, partly assembled. After
Insert the battery into the blower.
unpacking, check that the device is complete and install unassembled
Switch ( 4 ) is used for switching on/off.
components in accordance with the manual.
To turn the blower on, move the switch ( 4 ) forward to position 1 (1st
:
gear) or 2 (2nd gear).
Prior to any assembly or adjustment, make sure that
To turn off the blower, move the switch ( 4 ) back to position 0.
the device is disconnected from the battery.
n
General operating principles
n
Installation of the blower tube
When working with the garden blower always follow the relevant
CAUTION Do not use the blower without the tube installed.
guidelines specified in this instruction manual. It is designed to allow the
Connect the lower part of the tube ( 1 ) with the upper part ( 2 ) by pushing
user to operate it in an upright position (see Fig. D ). Any other position
the upper part into the lower part until a click occurs.
may result in injury. Never turn on the blower when it is lying on its side or
Mount the assembled tube on the device housing, until the unlocking
turned upside down.
button ( 3 ) clicks ( A ).
MAINTENANCE AND STORAGE :
To remove the tube, perform the above in reverse order.
CAUTION Before performing any maintenance work, switch off the device
CAUTION Before tube disassembly disconnect the machine from the
and disconnect it from the battery.
battery.
CAUTION Be careful not to get the blower wet. Never spray it with
water.
In general, the machine does not require special maintenance activities.
In order to ensure safe and efficient operations, it is recommended to
clean the device immediately after each use. After work, dirty elements
and ventilation openings are to be cleaned with a brush.
You can check the battery level with the battery level indicator button
Use a damp cloth with a mild detergent to clean the housing. Do not use
A single LED means the battery level is low, two LEDs mean
solvents or agents that might damage plastic parts of the device.
medium level, and three LEDs mean full battery.
The tool must be stored in a place that is not accessible to children and
must be kept clean and protected from moisture and dust. The storage
conditions should prevent potential mechanical damage and impact of
the weather conditions.
TRANSPORTATION:
Connect the battery to the charger
Connect the adapter plug to the charger .
Connect the adapter
to a mains socket (1 1 0–240 V, 50 - 60 Hz).
If the battery is removed for transport or storage, make sure the contacts
will not short circuit. Remove metal items such as screws, nails, clasps,
loose bits, wires, or metal filings from the case or transport container or
otherwise prevent them from touching the battery.
Connect the battery to the charger
PROTECTION OF THE ENVIRONMENT:
NOTE: The symbol nearby denotes that old equipment must
Battery charging indicator
never be thrown away together with other waste (with the
A green LED light indicates that the charger is connected to a power
penalty of a fine). Hazardous components of electronic
source. After the battery is connected, the red LED is on to indicate
equipment may adversely affect the natural environment and
charging. Blinking green battery LEDs also indicate that the battery is
human health.
charging and show the current battery level.
Each household may contribute to the recovery and reuse (recycling) of
When the battery is fully charged, the red LED goes off and the green LED
old machinery and equipment. Both in Poland and Europe a system for
is on.
recovery of used equipment either exists or is being created. The system
obliges all organizations that sell such equipment to collect the used
After charging, disconnect the charger and remove the battery.
machinery and appliances. Moreover, general purpose collecting points
NOTE! The battery may get slightly hot when charging. This is not a
for such equipment are available.
malfunction.
The lithium-ion battery can be charged at any moment, without
MANUFACTURER:
detriment to its life. Interrupting the charging process does not entail a
PROFIX Co.Ltd.,
risk of damaging the battery cells.
34 Marywilska Street,
03-228 Warsaw, POLAND.
n
Turning on/off
NOTE
!
see Fig.
!
!
!
n
Charging the battery
NOTE! Battery and charger are not part of the delivery . Depending on your
needs, you can purchase a 1.5 Ah battery TJ15AK or 2.0 Ah battery TJ2AK
and a compatible charger TJ3LD (charging time 3–5 hours) or TJ1LD
(charging time 1 hour).
( see Fig. B )
Charge the battery fully
before use.
TJ3LD
The first charging procedure using TJ3LD should last at least 5 hours.
1. Press the battery lock button ( 6 ) and remove the battery ( 7 ) from the
blower ( see Fig. A ).
Transport and store the device in a package that protects it against
2. ( 7 ) ( 10 ) ( see Fig. B ).
moisture, penetration of dust and small objects, in particular secure
3.
ventilation openings. Small particles (objects) penetrating into the
4. ( 11 )
housing can damage the motor.
TJ1LD
The first charging procedure using TJ1LD should last at least 1 hour.
1. Press the battery lock button ( 6 ) and remove the battery ( 7 ) from the
blower ( see Fig. A ).
2. ( 7 ) ( 10 ) ( see Fig. C ).
3. Connect the charger plug to a mains socket (220–240 V, 50 Hz).
n
OPERATION:
( 8 )
.
Charger
Charger