7
provided in the outer ring of the skirt, enabling free
movement when in use (Fig.5).
4.9 Fitting the vacuum unit
•
Stand machine upright, and clamp the vacuum unit
support bracket to the handle tube in the specified
position. (Refer to the instructions supplied with the
unit).
•
Rest the vacuum unit on the support bracket with
the control switch to the rear, and engage the
locking bar on the back of the unit to secure it in
position.
•
Push the flexible hose on to the vacuum unit and
skirt.
•
Plug the electrical lead from the vacuum unit into
the socket situated on the left side of the handle
moulding.
•
The machine is now ready for use. The switch
controlling the vacuum unit is located on the back of
the unit. The OFF position is marked O.
4.10 Using the vacuum unit
IMPORTANT - For maximum suction the sliding
shutter on the top of the unit must be closed.
•
Dust collected by the unit is contained within the
filter bag located behind the front cover.
•
To replace the filter bag, switch off vacuum unit,
release front cover catch and lift off cover.
•
Remove and dispose of used bag. Fit new bag
and replace front cover.
5. Storage
Always unplug and wipe down and dry the machine
after use. The machine should normally be stored
with the handle in the fully upright position.
Wrap supply cord around the handlebar and cable
winder ensuring that the plug is not trailing on the
floor. Store the machine in a dry indoor area only.
Never store the machine with a pad fitted as this
causes distortion, and results in instability during
operation.
6. Maintenance
WARNING - Before undertaking maintenance
operations or adjustments switch off machine
and unplug from the electricity supply.
The machine requires minimum maintenance apart
from the following checks by the operator.
•
Supply cord
- Regularly inspect sheath, plug and
cord anchorage for damage or loose connection.
•
Solution tank
- Check water flow, if restricted
inspect hoses and tubes for blockage or kinks.
Dismantle control valve to clean if necessary.
Check switch interlock for correct operation.
•
Vacuum unit
- All dust bags must be changed
regularly and hoses and connectors checked for
blockage to avoid unsatisfactory results.
•
Motor overload cut-out
- All machines are fitted
with an automatic reset motor overload cut-out.
The cut-out will operate to protect the motor from
overheating by switching the machine off when
there is excessive friction/resistance to the
cleaning head on the floor. This is usually caused
by the stickiness of the pad or floor. Turn the
cleaning pad over or if both sides are dirty
replace with a clean pad. It is not possible to
obtain a good finish on the floor using a dirty pad.
Should the cut-out operate it will reset
automatically when the motor has cooled
sufficiently, usually after 15 - 30 mins.
IMPORTANT
- Should the machine fail to operate
contact the supplier from whom you purchased the
machine.
7 After sales service
Should you require after sales service please contact
the supplier from whom you purchased the
machine,who will arrange service. Repairs and
servicing of Truvox products should only be
performed by trained staff. Improper repairs can
cause considerable dangers to the user.
8 Guarantee
Your product is guaranteed for two years from the
date of purchase, or hire purchase, against defects in
materials or workmanship during manufacture. Within
the guarantee period we undertake to repair or
replace free of charge to the purchaser, any part
found to be defective, excluding brushes, drive discs
and vacuum skirts.
No liability is accepted for damage caused by
accident, misuse or neglect, or the fitting of other than
genuine Truvox parts. Truvox International Limited
cannot accept reponsibility for repairs performed by
persons other than a Truvox serivce engineer or an
authorised service agent.
This guarantee is in addition to your statutory rights
and does not affect your rights under the Supply of
Goods (Implied Terms) Act 1973, or in general.
Truvox International Limited policy is one of continual
product development and we reserve the right to alter
specifications without prior notice.