7
3
Preparing for use
3.1 Fitting the handle
1
Carefully remove the machine base and
handle from their respective packaging.
2
Check that the following items are present
with the base:-
- M8 x 70 Bolt (3)
- Nyloc Hex. nut (3)
- Plain washer (6)
- 13mm A/F Spanner (2)
3
Take handle and check that ‘O’ rings on
either side of the knuckle pivot are seated in
their grooves, and that the datum mark on
the pivot gear is aligned with the handle tube.
If this is not the case, raise the handle
adjustment lever and rotate the pivot gear
until the datum mark is in line with the handle
tube, and release the adjustment lever.
4
With the handle held vertically and cable
winder to the rear, lower pivot between the
raised flanges on the machine base.
5
Align holes in pivot with those on base and fit
the three M8 bolts, washers and nuts, and
tighten using the spanners supplied (Fig.1).
6
Connect supply lead from handle to socket
on motor housing.
4
Controls
The operating controls for all models are located
on the handle (Fig 2 ).
1 - Switch trigger, left hand
Used to switch motor ON and OFF. Can only
be operated with handle in working position,
and if left hand interlock button (2) has
previously been depressed
2 - Interlock button, left hand
This must be depressed initially to enable left
hand switch trigger to switch motor on.
3 - Switch trigger, right hand
Used to switch motor ON and OFF. Can only
be operated with handle in working position,
and if right hand interlock button (4) has
previously been depressed.
4 - Interlock button, right hand
This must be depressed initially to enable
right hand switch trigger to switch motor on.
5 - Handle adjustment lever
Used to adjust handle to comfortable working
height.
Note:
For safety reasons the machine
cannot be operated unless the handle is
moved to a working height.
6 - Solution feed lever
Operates flow valve in solution tank (if fitted).
- Pull lever to release solution.
- Release lever to stop flow.
7 - Socket connector
Connection point for vacuum unit lead.
Drive plate
Attachment point for brush or drive disc and
pad.
Cable winder
Used to hold supply cord in place on handle
when machine is not in use. Can be turned to
enable quick release of cord.
Motor overload cut-out
Protects motor from overload and possible
damage. The cut-out will reset automatically
when cooled sufficiently, enabling the motor to
restart.
Neon indicator
(on handle)
Lights when the machine is connected to the
power supply
.
5
Fitting a brush or drive disc and pads
WARNING - This appliance has been
designed for use with the pads
specified by the manufacturer. The
fitting
of
other
pads
may
affect
its
performance and safety.
Always ensure machine is unplugged before
fitting or removing parts.
•
Adjust handle to the fully upright position.
•
Pull handle down until it rests on the floor and
the brush guard is raised.
•
Fit the brush/drive disc onto the drive plate and
rotate it anti-clockwise until secure.
•
Return machine to upright position.
•
IMPORTANT - Never allow the cleaning
head to rest on the brush or drive disc and
pad when not in use.
6
Adjusting the handle height
Select the most comfortable handle height using
the adjustment lever as previously described (see
Controls
) and lock in position.
7
Operation
The normal movement of a machine in use is
from side to side across the floor. This is
achieved automatically by raising or lowering the
handle whilst it is engaged in the normal working
position.
Lowering the handle thereby increasing the
pressure at the rear of the brush/drive disc,
moves the machine to the left. Raising the handle
increasing the pressure on the front of the
brush/drive disc moves the machine to the right.
Effective cleaning and polishing is achieved by
moving the machine in a
backwards
direction.
Do not
leave the machine standing on a brush or
drive disc and pad when not in use.
7.1 Starting the machine
•
Fully unwind the supply cord from the handle
and plug into a convenient socket outlet. The
neon indicator on the handle should light
showing that power is available.
•
With the handle set at a convenient working
height and with both left and right hands on the
handle, depress both interlock buttons with the