Truma Mover S, Инструкция по установке и эксплуатации

Страница: 7 / 16

7
Installation instructions
Read the installation instructions prior to starting work and
follow them carefully!
Please ensure that no metal chips or other contaminants get
into the controller during installation.
Intended use
The Mover S has been built for use with single-axis caravans
with a gross weight of up to 1800 kg.
The Mover S weighs approx. 35 kg with the cross
actuation device attached.
Check the towing load of your vehicle and the gross weight of
your caravan in order to establish whether they are designed
for the additional weight.
Approval
The Truma Mover S has design approval, and a general oper-
ating permit (ABE) has been issued for Germany. Acceptance
by a vehicle expert is not required (except when installing the
low chassis kit). The ABE can be requested from Truma and
must be carried in the vehicle in Germany.
The Mover S complies with the vehicle engine interference
suppression directive 72/245/EEC with supplements
2004/104/EC, 2005/83/EC and 2006/28/EC and bears type
approval number:
e1 03 4473.
The Mover S complies with EMC directive 89/336/EEC.
The remote hand set and the receiver comply with the
requirements of the R&TTE directive 1999/5/EC.
The technical and administrative regulations of the country in
which the vehicle is initially registered must be complied with
when the Mover is being installed.
Any modifications to the unit, or the use of spare parts and
accessories that are important to the operation of the system
that are not original Truma parts and failure to follow the in-
stallation and operating instructions will cancel the warranty
and indemnify Truma from any liability claims. In addition to
this, the operational approval for the device will be cancelled.
Tools and facilities required
To install the unit you will need:
– 13 mm, 17 mm, 10 mm socket wrench, ring spanner or
open-jawed spanner
– Torque wrench (20 – 40 Nm)
– Cable cutter / Crimping tool
– Power drill / screwdrivers / 25 mm hole cutter
– Portable 2 tonne trolley jack and axle stands to suit
– Appropriate lighting
Minimum installation dimensions
The equipment can only be fitted to caravans / trailers within
the following dimensions.
min. 180*
max. 1860
max. 2400
min. 60
min. 30
max. 48
opt. 185
min. 2.8
max. 3.5
Caravan floor
•
all dimensions in mm
* with fully loaded vehicle
A distinction is made between L-profiled and U-profiled
chassis as shown in the illustration.
Caravan floor
L-profiile
U-profile
Measuring the chassis height
Frame height (Y) measured at distance of 106 mm (X) from
the outer edge of the tyre at height of hub / middle of tyre.
Determining the installation type
1. Standard installation
Standard installation is used with a U-profile or L-profile chas-
sis and a frame height (Y) of approx. 185 mm.
No special
accessories are required.
2. Installation with chassis with U-profile or L-profile
and frame height of between 140 and 185 mm
With a chassis with a frame height (Y) of 140 mm to 185 mm,
1, 2 or 3
spacer plate sets and the screw set are needed to
compensate for the height.
3. Installation with chassis with U-profiles or L-profiles
with frame height of less than 140 mm
With a chassis with a frame height (Y) of less than 140 mm a
low chassis kit must be fitted to compensate for the height.
In Germany, the low chassis kit installation must
be accepted by a vehicle expert.
4. The AL-KO Vario III / AV installation kit must be used
with the AL-KO Vario III / AV chassis with a frame thickness of
less than 2.8 mm.
5. Installation with Eriba Touring chassis
The Eriba Touring mounting set is needed for the Eriba Touring
chassis.