background image

6

IR receiver and manual on / off

There is an additional pushbutton on the receiver (m), with 
which the unit can also be switched on and off without the 
remote control (e.g. with a ballpoint pen).

If the unit is switched on using this pushbutton, the system is 
automatically reset to the factory settings (Automatic mode, 
22 °C).

IR receiver / operating indicator

LED 3

LED 2

LED 1

m

LED 1 blue – permanently on – (cooling mode)
LED 1 blue – flashing – (cooling mode compressor start-up) 

LED 2 yellow – permanently on – (heating mode)
LED 2 yellow – flashing – (heating mode compressor start-up)

LED 3 red – flashing – (data is being transmitted)
LED 3 red – permanently on – (fault)

Red LED illuminates

The unit is indicating a fault. Switch unit off, wait for a short 
time and switch on again. If the red LED continues to illumi-
nate, please contact Truma Service.

Air distribution

Right / left

Two individually adjustable air outlets at the front, and two at 
the rear.

Front / rear

The air flow can be split so that specific quantities are fed into 
the front and rear areas of the vehicle.

Ceiling / floor

The air flow can be deflected from the ceiling to the floor.

right / left

right / left

right / left

right / left

IR receiver /
operating indicator

front / rear

ceiling / 
floor

ceiling / 
floor

fr

ont 

fr

ont 

rear

rear

Changing the battery in the IR remote control

Please be sure to use leak-proof micro-batteries only, 
type LR 3, AM4, AAA, MN 2400 (1.5 V). 

The battery compartment is located on the rear of the remote 
control unit.

When fitting new batteries, ensure the 
polarity (positive/negative) is correct!

Dead and used batteries may leak 
and damage the remote control 

unit. Remove the batteries if the remote 
control is not going to be used for an ex-
tended period.

No claims under guarantee will be considered for dam-
age caused by leaking batteries.

Before throwing away a defective remote control, it is es-
sential that the batteries be removed and disposed of in the 
proper manner.

Maintenance

Filter changes should be carried out depending on the 
amount of use, but we recommend a change at least every 
12 months. Never operate the air conditioning system without 
a filter, since this can decrease performance. Always keep the 
air inlets / air outlets and condensation traps on the roof free 
from obstructions such as leaves. Use a soft, clean cloth to 
clean the air conditioning system.

Disposal

The device must be disposed of in line with the administra-
tive regulations of the respective country in which it is used. 
National regulations and laws (in Germany, for example, the 
End-of-life Vehicle Regulation) must be observed.

In other countries, the relevant regulations must be observed.

Содержание Aventa comfort













Отзывы: