True Manufacturing Company TR1RRI-1S Скачать руководство пользователя страница 21

............ www.truemfg.com ............

True Food Service Equipment, Inc.

19

19

•  Disconnect power to unit.
•  Three door units will need the rainshield removed to 

easily access the condenser coil for cleaning. Back out the 

top screws (see image 2) and the bottom screws (see image 

3) anchoring the rainshield. Unplug the wires connected 

to the rear of the digital temperature thermometer (see 

image 3) and set the rainshield to the side.

NOTE (For Three Door Units Only) 

Remember to mark which wire plugs into the rear of the digital 

temperature thermometer for easy assembly of the rainshield.

•  Clean off accumulated dirt from the condenser coil 

and the fan with a stiff bristle brush. After brushing the 

components off vacuum all dirt residue from the coil, fan, 

and surrounding areas.

NOTE 

Single door freezer models are supplied with a long handle 

stiff bristle brush. This brush is used to reach through tight 

clearances when cleaning the condenser coil (see image 1).

MAINTENANCE, CARE & CLEANING

CLEANING THE CONDENSER COIL

When using electrical appliances, basic safety precautions should be followed, including the following:

Single Door Freezer unit
(Brush Provided)

Three Door Freezer unit
(Rainshield Removal/top 
screws)

Three Door Freezer unit
(Rainshield Removal / bottom 
screws)

Digital Temperature Control Connections.
(Rainshield Removal)

1

2

3

4

MAINTENANCE, CARE & CLEANING

Содержание TR1RRI-1S


























Отзывы: