True Manufacturing Company TGU-2 Скачать руководство пользователя страница 13

............ www.truemfg.com ............

True Food International Equipment, Inc.

11

11

A.

  Cabinet is plugged in.

 

–  Display will illuminate.

B.

  After the LAE control preprogrammed time delay of 3 minutes, the compressor 

and evaporator fan(s) will start if the control is calling for cooling.

 

–  Control may be programmed so at the start of every compressor cycle 

the condenser fan(s) will reverse for 30 seconds to blow dirt off the 
condensing coil.

C.

  The LAE control will cycle the compressor and evaporator fan(s) on and off 

together determined by the Set-Point and Differential temperatures. (If the 
Set-Point needs to be changed due to conditions please see instructions  
on the following pages.)

 

–  The 

Set-Point

 is the preprogrammed temperature which shuts off the 

compressor and evaporator fan(s).

 

–  The 

Differential

 is the preprogrammed temperature that is added to the 

Set-Point temperature that will start the compressor and evaporator 
fan(s).

 

Example:

  

If the Set-Point is -9°F/-23°C and the Differential is 10°F/5°C 

  

(Set-Point) -9°F + 10 (Differential) = -1°F 

  

Or 

  

(Set-Point) -23°C + 5 (Differential) = -18°C 

  

The compressor and evaporator fan(s) will cycle off -9°F/-23°C  

  

and back on at -1°F/-18°C

D.

  The LAE control may be preprogrammed to initiate defrost at specific times of 

day or intervals. (If additional Defrost Intervals / Cycles are needed or a manual 
defrost is required due to conditions please see instructions on next 
page(s).)

 

–  At this time the compressor and evaporator fan(s) will turn off and the 

evaporator coil heater and drain tube heater will be energized until a 
preprogrammed temperature or duration is reached.

 

–  The evaporator fan(s) will remain off until a preprogrammed temperature 

of the evaporator coil is reached.

LAE CONTROL FOR TGU FREEZERS

SEQUENCE OF OPERATION

True Manufacturing recommends that ONLY the Set-Point and/or  

Defrost Interval may be adjusted due to certain conditions.

If you have any questions, please contact the Technical Service Department.

 

TRUE EUROPE • Fields End Road • Goldthorpe • NR, Rotherham • South Yorkshire UK

UK Office/Tec44 (0) 1709 888 888 • UK Free Phone 0800 783 2049

UK Free Phone from France, Germany, Netherlands, Belgium & Republic of Ireland 00-880-8783-4685

TRUE FOOD INTERNATIONAL, INC. • 2001 East Terra Lane • O’Fallon • Missouri • 63366-4434 • USA

USA Office/Technical (001) 636-240-2400 • Email [email protected]

Содержание TGU-2

























Отзывы: