background image

P-47D Thunderbolt

Specification:

Length             :1463 mm(57.6")

Wing Span       :1800 mm(73.2")

Wing Area        :55.3 sq. dm

                        5.95 sq. ft

Wing  Loading  :117.5 g/sq. dm

                        38.5 oz/sq. ft

Flying Weight   :6.5 kg(14.3 lbs)

Radio               :6ch&9 servos

Engine             :108  2-cycle 

                        120  4-cycle

SAFETY PRECAUTIONS

INSTRUCTION MANUAL

First-time builders should seek advice from people having building 

experience.If misused or abused,it can cause serious bodily injury 

and damage to property.

Fly only in open areas and preferably at a dedicated R/C flying site.

We suggest having a qualified instructor carefully inspect your 

airplane before its first flight.Please carefully read and follow all 

instructions included with this airplane,your radio control system 

and any other components purchased separately.

(The people under 18 years old is forbidden from flying this model)

This R/C airplane is not  a toy!

Air tank

Switch

Air inlet

     3-way

pressure inlet

     3-way

pressure inlet

     3-way

pressure inlet

The status when the

gear up 

Pull out length of 8mm 

to make gear down 

Air valve

Air valve

Make sure to assemble retracts as instructed below.

Two wheel retract system

Quick release connector  

Quick release connector  

Pressure reduction inlet  

Strut 

Strut 

3-way pressure inlet

3

Pressure reduction inlet

1

1

Air tank

1

Air inlet

2

1
1

Air line (3000mm)

2

Quick release connector  

Strut( 90 ) 

Switch

Clevis

Rod (2X300mm)

1

1

1

Retainer

TP Screw(2x14mm)

2

Ø1.7mm

Ø0.2mm

Pleas notice the inner diameter for each 

side of the pressure reduction inlet. 

Please insure the sealing of the retract 

system before flight .

20mm

20mm

AILERON

Side View 

AILERON

40mm

FLAP

FLAP

136mm

Adjustment.

The centre of the Gravity.

71

14

70

Содержание P-47D Thunderbolt









Отзывы: