background image

Models:  JP30, JP30L 

Electric Towbarless Tug 

 

07/2015 | Rev. 10 

Page | 7 

 
6.1 

LOADING AIRCRAFT 

(continued) 

4.  Secure the aircraft nose wheel with the safety strap. The safety strap is a strap with 

a ratchet mechanism and spring clip hooks at each end. On either side of the 
forward end of the cradle are brackets that have a hole in each of them. These 
holes on either side are used for the safety strap. After the aircraft has been 
winched onto the cradle hook one end of the safety strap to one side of the cradle 
and position the strap up and over the top of the nose wheel (or nose wheel pant) 
and in front of the oleo strut. Hook the other end into the hole on the other side of 
the cradle and use the ratchet to snug up the strap. Be very careful not to position 
the strap where it might damage some component of the nose wheel assembly. Do 
not over tighten as it only needs to be snug enough to prevent the nose wheel from 
possibly lifting upward out of the cradle. On some aircraft with nose wheel pants it 
may make sense to run the safety strap through a scissors on the aft side of the 
strut. 

5.  If the aircraft has a single nosewheel versus a dual nosewheel then 

the moveable side plates will be needed in order to keep the nose 
wheel from twisting or rotating while the aircraft is being moved. 
Once the nose wheel is in position on the cradle, lift up on the ring of 
the index plunger on top of the square tube on the cradle and slide 
the moveable side plate in the proper direction. If you release the 
ring on the plunger when you start to reposition the side plate it will 
drop into the next available hole of the inner square tube. 

6.  Raise the lift cradle high enough to clear obstacles on the ground. 
7.  If moving aircraft over 15,000 lbs make sure the transaxle is in LOW 

gear. The knob for this is located on the right side of the transaxle 
as you are standing on the cradle looking aft towards the steering wheel. There is a sticker on the front center of the 
transaxle that shows to push the shaft all the way in (to your left) to place it in low gear. 

8.  Move the aircraft by slowly advancing the accelerator lever in the direction of travel. 
9.  For moving aircraft up or down inclines/slopes, a qualified operator should be in the aircraft cockpit to 

utilize the aircraft’s 

brakes for safety/backup. 

 
6.2 

UNLOADING AIRCRAFT 

1. 

To unload aircraft, lower lift cradle to a position 1/2” above the ground. Remove strut strap and safety strap. 

2.  Chock the aircrafts main wheels and then back JETporter away from the aircraft, allowing the nose wheel of the aircraft to 

roll off lift cradle onto the ground. 

 

7.0 

GROUND POWER UNIT 

7.1 

DESCRIPTION 

1.  The ground power unit (GPU) is an integral part of JETporter

.

 The traction batteries serve as the source of power to start 

the aircraft. 

2.  The black terminal is the negative, terminal. Always connect the black plug into the black terminal. This provides the 

ground connection to the aircraft. 

3.  The first red terminal is the 12 volt terminal. With the batteries in a fully charged condition, the terminal voltage will be 

closer to 14 volts. With the batteries in a partially charged condition, the voltage will be typically closer to 12 volts. To 
assist a 12 volt aircraft, plug the black lead into the black terminal and the red plug into the 12 volt terminal. 

4.  The second red terminal, labeled 24 volt, is used to start aircraft with 24 volt systems. Plug the black plug into the black 

terminal and the red plug into the 24/ volt terminal. When the batteries are in a fully charged condition, the voltage will be 
near 26 volts. As the batteries are used, the voltage will decrease to nearly 24 volts. 

5.  The third red terminal, labeled 30 volt, may be used to start 28 volt aircraft, especially in cold weather, or when conditions 

require additional voltage. Check with the aircraft owner/operator to make sure the increased voltage is within the 
aircraft’s electrical system tolerances. When the batteries are in a fully charged condition, the voltage will be near 31 volts. 
This increased voltage will make starting easier. 

CAUTION

 

Do not use the 30 volt terminal unless the aircraft electrical system is isolated from the starting circuit. The 
over voltage could damage the aircraft’s electrical system. 
 

6.  The GPU positive voltage is connected directly to the traction batteries and does not have a fuse in the circuit. Pressing 

the E-stop will disconnect the negative side of the GPU circuit. Be extremely careful when handling the GPU cables. 
Extremely high currents are possible. 

 
 
 
 
 

7.1 Description continued on following page. 

JP-065 

JP-090 

Содержание JP30




















































































Отзывы: