Trolex TX6383 Series страница 12 Скачать руководство пользователя

Страница: 12 / 28

FLAMMABLE GAS SENSOR/TRANSMITTER

A T E X

GROUP I & II

INTRINSICALLY

SAFE

6 CONNECTIONS

continued

6.3

5 to 15 Hz Output Signal

A square wave, frequency variable output
that is proportional to the measured value.
The output device is an open collector NPN
transistor.

Output:

5 to 15 Hz

(zero = 5 Hz)
(span = 15 Hz)

Maximum Voltage:

15.4 V

Maximum Current:

2 mA

Minimum Pulse Rise Time:

5 V/ms

1 2 3 4 5 6 7 8

0 V

5 to 15 Hz signal

+V Supply

A
may be required
at the monitoring
device.

0 V Supply

TX6383

Monitoring

Device

A pull up resistor may be required

at the monitoring device.

6.4

Using Gas Sensors in Hazardous Areas

6.4.1

GROUP I HAZARDOUS AREAS (MINING)

TX6383.01

FLAMMABLE GAS SENSOR/ TRANSMITTER

All options of the TX6383.01sensor (0.4 to 2 V, 4 to 20 mA and

5 to 15 Hz) are certified Intrinsically Safe for use in Group I

hazardous areas (Mining) when used with approved equipment

eg. TX9131 Trip Amplifier or a TX9042 Programmable

Sensor Controller.

THE COMPLETE SYSTEM, BOTH SENSOR AND MONITORING

DEVICE, CAN BE MOUNTED IN THE HAZARDOUS AREA.

The interconnecting cable between the sensor and the

monitoring device must have steel wire armoured

protection or a braided earth screen. The cross sectional

area of the conductors must be a minimum of 1 mm

TX9131

HAZARDOUS

SAFE

TX6383.01

15 Hz

6.4.2

GROUP II HAZARDOUS AREAS (24 V dc)

TX6383.02

TOXIC GAS SENSOR/ TRANSMITTER

This version of the sensor (4 to 20 mA) is certified Intrinsically

Safe for use in industrial hazardous areas, when used in

conjunction with safety barriers.

THE SAFETY BARRIERS ARE MOUNTED IN THE SAFE AREA,

ONLY THE SENSOR IS MOUNTED IN THE HAZARDOUS AREA.

The system may be used with either zener safety barriers or

isolation safety barriers.

4 to 20 mA
Signal

HAZARDOUS

SAFE

TX6383.02

12/28

INSTALLATION & OPERATING DATA

APPLICATION

GROUP I HAZARDOUS AREAS

TT X

X 66 33 88 33

ISSUE S 01/15

Содержание TX6383 Series





























Результаты поиска

Содержание TX6383 Series

Отзывы:

Похожие инструкции для TX6383 Series

Бренды по названию

Популярные бренды

Trolex TX6383 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TX6383 Series

Отзывы:

Похожие инструкции для TX6383 Series

Бренды по названию

Популярные бренды