Triton ASPIRANTE THERMOSTATIC POWER SHOWER Скачать руководство пользователя страница 25

Страница: 25 / 28

Aspirante thermostatic power shower

FAULT FINDING (continued)

Symptom Cause

Action/Cure

It is advised all electrical maintenance/repairs to the shower

should be carried out by a suitably qualified person.

In the unlikely event of a fault occurring please

contact Triton Customer Service. Do not remove

the shower from the installation.

Water does
not flow or is
reduced.

Cross flow of

hot and cold
water into
system.

Water

dripping from
showerhead
when turned
off.

4.1

Water supplies cut off.

4.2

Shower blocked or air

in the system.

4.3

Showerhead blocked.

4.4

Blocked filters.

5.1

Dirt/debris in check

valves.

6.1

Debris in solenoid

valve.

6.2

Potentiometer faulty.

4.1.1

Check water elsewhere in house and

if necessary contact the local Water
Company.

4.2.1

Switch off shower and contact Customer

Service.

4.3.1

Clean showerhead.

4.4.1

Clean filters.

5.1.1

Isolate water to unit. Remove check valves.

Clean and replace.

6.1.1

Call Customer Service.

6.2.1

Call Customer Service.

Содержание ASPIRANTE THERMOSTATIC POWER SHOWER





























Результаты поиска

Содержание ASPIRANTE THERMOSTATIC POWER SHOWER

Отзывы:

Похожие инструкции для ASPIRANTE THERMOSTATIC POWER SHOWER

Бренды по названию

Популярные бренды

Triton ASPIRANTE THERMOSTATIC POWER SHOWER, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ASPIRANTE THERMOSTATIC POWER SHOWER

Отзывы:

Похожие инструкции для ASPIRANTE THERMOSTATIC POWER SHOWER

Бренды по названию

Популярные бренды