Tritium Veefil-RT 175-S Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 25

background image

Veefil-RT 175-S Site Installation Manual

TRI125.INS.018 version 1

4 March 2020

Manual

Page 19 of 25

4.7

User unit installation

4.7.1

Foundation preparation

Note:

If the user unit is to be located a distance greater than 100m from the IPU, optical fibre

is required for communication in place of Cat6a.

Foundation design and preparation is the responsibility of the customer. Device footprints
are provided by tritium for hole drilling and conduit / cable location guidance. For further
details, please refer to

TRI125.INS.001 Veefil-RT175-S User Unit Installation Manual.

Note:

A mounting stencil may be supplied by tritium at customer request.

Figure 14: User Unit Baseplate Dimensions

Ensure that all cables are pulled and labelled correctly.

Ensure that conduits are cut to 70mm from the foundation ground.

Cut the M16 mounting rods down to 50mm from the foundation ground.

Note:

Do not use less than M12.

Clean the foundation of any debris.

Inspect the mounting rods to ensure they are straight, and the threads are clean.

«
...
17
18
19
20
21
...
»

Содержание Veefil-RT 175-S


























Отзывы:

Нет отзывов

Похожие инструкции для Veefil-RT 175-S

Бренд: UFESA Страницы: 27

AVCCAM AG-HMR10

Бренд: Panasonic Страницы: 4

Бренд: AA Products Страницы: 8

MARTEN-FREE CAR

Бренд: Gardigo Страницы: 36

Бренд: IFM Страницы: 12

Бренд: IFM Страницы: 13

Efector 200 Series

Бренд: IFM Страницы: 4

Бренд: Vauxhall Страницы: 2

Бренд: IFM Страницы: 33

Бренд: X-lite Страницы: 6

Бренд: Razor Страницы: 2

RAZORX LONGBOARD

Бренд: Razor Страницы: 16

Бренд: RayTek Страницы: 93

Бренд: Xerox Страницы: 16

Бренд: Yealink Страницы: 6

WINE CAPTAIN U-2115WCOL-00

Бренд: U-Line Страницы: 5

Бренд: 2E GAMING Страницы: 26

Бренд: Öhlins Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды