4R
Feature Identification
Identify the premium features on your specific model and quickly locate instructions on how to maximize their use.
Configuration DIP
Switches:
optimize Inverter/Charger
operation depending on your application. See pages 6-7 for
setting instructions.
Operating Mode Switch:
controls Inverter/Charger operation.
The “AUTO/REMOTE” setting ensures your equipment
receives constant, uninterrupted AC power. It also enables the
Inverter/Charger to be remotely monitored and controlled with
an optional remote module (Tripp Lite model APSRM2, sold
separately or included with select models). The “CHARGE
ONLY” setting allows your batteries to return to full charge faster
by turning the inverter off which halts battery discharging. See
page 5 for setting instructions.
Operation Indicator Lights:
intuitive “traffic light” signals
show whether the Inverter/Charger is operating from AC line
power or DC battery power. It also warns you if the connected
equipment load is too high. See page 5 for instructions on
reading indicator lights.
Battery Indicator Lights:
intuitive “traffic light” signals show
approximate charge level of your battery. See page 5 for
instructions on reading indicator lights.
DC Power Terminals:
connect to your battery terminals. See
page 10 for connection instructions.
Ground Fault Interrupter (GFI) AC Receptacles (not on
hardwire models):
allow you to connect equipment that would
normally be plugged into a utility outlet. They feature ground
fault interrupter switches that trip if there is excessive current
on the ground safety wire.
AC Input Cord (not on hardwire models):
connects the
Inverter/Charger to any source of utility- or generator-supplied
AC power. See page 11 for connection instructions.
Hardwire AC Input/Output Terminals (not on corded
models):
securely connect the Inverter/Charger to vehicle or
facility electrical system input and recommended GFCI receptacle
output. See page 11 for connection instructions.
Resettable Circuit Breaker:
protect your Inverter/Charger against
damage due to overload. See page 5 for resetting instructions.
Remote Control Module Connector:
allows remote monitoring
and control with an optional module (Tripp Lite model
APSRM2, sold separately or included with select models). See
remote module owner’s manual for connection instructions.
Battery Charge Conserver (Load Sense) Dial (not on 612
models):
conserves battery power by setting the low-load level
at which the Inverter/Charger’s inverter automatically shuts off.
See page 7 for setting instructions.
Main Ground Lug:
properly grounds the Inverter/Charger to
vehicle grounding system or to earth ground. See page
10 for connection instructions.
Multi-Speed Cooling Fan:
quiet, efficient fan prolongs equipment
service life.
DC Power Terminal Cover Plate
Hardwire AC Input/Output Cover Plate
Battery Temperature Sensing Connector (not on 612 models):
prolongs battery life by adjusting charge based on battery tem-
perature. Use with cable (included on select models). See page
7 for details.
Automatic Generator Start Connector (not on 612 models):
automatically cycles generator based on battery voltage. Use
with user-supplied cable. See page 7 for details.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
HOT IN
NEUTRAL IN
GROUND IN
GROUND OUT
HOT OUT
“FOR USE WITH COPPER WIRE ONLY”
NEUTRAL OUT
1
2
4
3
5
9
10
11
13
14
8
15
Front View (Single Input/Output Hardwire Models)
12
Rear View (Single Input/Output Hardwire Models and Select Corded Models)
AC IN 1
HOT - BROWN
NEU - BLUE
GND - GRN/YEL
AC IN 2
HOT - GRAY
NEU - WHITE
GND - GRN/YEL
AC OUT 1
HOT - BLACK
NEU - YELLOW
GND - GRN/YEL
AC OUT 2
HOT - ORANGE
NEU - RED
GND - GRN/YEL
1
2
4
3
5
9
10
11
13
Front View (Dual Input/Output Hardwire Models)
Front View (Corded Models)
* 612 models have only one set of DIP Switches. ** Select models include front-mounted ground lug. † Available on all models except 612 models.
2
4
3
5
6
7
9
10
11
†
13
14
1
*
12
**
8
16
17
16
†
17
†
Side Mounted,
Not Shown
Side Mounted,
Not Shown
16
17
Side Mounted,
Not Shown
Side Mounted,
Not Shown
16
17
12
