background image

12

Troubleshooting 

(continued)

Lights (On/Flashing) and Condition

Solution

On: BYPASS, LINE  

Check the UPS to be sure that there is 

Flashing: FAULT

adequate space for air to circulate near

Condition: On Bypass due to High  

the vents and that the fan is working

Internal Temperature

properly. Restart the UPS.

Flashing: LINE

This indicates that utility power is too high

Condition: Input Abnormal

or low for the UPS to operate in BYPASS 
mode, so if an inverter failure occurs, 
the UPS will deliver no output.

On: FAULT, 50%

Restart the UPS. If the problem persists,

Flashing: LINE

contact Tripp Lite for repairs.

Condition: No Output due to High 
Output Voltage and Abnormal Input

On: FAULT 

Restart the UPS. If the problem persists,

Flashing: LINE, 50%

contact Tripp Lite for repairs.

Condition: No Output due to Low
Output Voltage and Abnormal Input

On: FAULT, 25%

Restart the UPS. If the problem persists,

Flashing: LINE

contact Tripp Lite for repairs.

Condition: No Output due to High
Bus Voltage and Abnormal Input

On: FAULT

Restart the UPS. If the problem persists,

Flashing: LINE, 25%

contact Tripp Lite for repairs.

Condition: No Output due to Low
Bus Voltage and Abnormal Input

Flashing: LINE, FAULT

Check the UPS to be sure that there is

Condition: No Output due to High

adequate space for air to circulate near

Internal Temperature and Abnormal 

the vents and that the fan is working 

Input

properly. Restart the UPS. If the problem
persists, contact Tripp Lite for repairs.

12

200507084 93-2474 SMARTONLINE HT OM.qxd  10/20/2005  11:11 AM  Page 12

Содержание Audio/Video On-Line UPS System

















Отзывы: