background image

 
 

  

 

Temperature (air): Thermistor 

Operating Conditions -20 to 50

o

C (-4 to 122

o

F) CO

2

 sensor 

  

 

0 to 50

o

C (32 to 122

o

F) CO sensor 

  

 

-20 to 50

o

C all other parameters 

Storage Conditions 

-20 to 60

o

C (-4 to 140

o

F); 10 to 90% RH non-

condensing 

Power Supply 

 

4 x 1.5V ‘AA’ batteries or AC adaptor (9V) 

Battery Life 

 

approx. 24 hours (alkaline batteries) 

Dimensions / Weight 

205 x 70 x 56mm (8.1 x 2.8 x 2.2“) / 200g (7.1 
oz.) 

 
 

 
 
 

Warranty 

 

 
Triplett / Jewell Instruments extends the following warranty to the original purchaser of 
these goods for use. Triplett warrants to the original purchaser for use that the products 
sold by it will be free from defects in workmanship and material for a period of (1) one 
year from the date of purchase. This warranty does not apply to any of our products 
which have been repaired or altered by unauthorized persons in any way or purchased 
from unauthorized distributors so as, in our sole judgment, to injure their stability or 
reliability, or which have been subject to misuse, abuse, misapplication, negligence, 
accident or which have had the serial numbers altered, defaced, or removed. 
Accessories, including batteries are not covered by this warranty 

 

Copyright © 2020 Triplett 

 

www.triplett.com 

 

 

Содержание GSM450





















Отзывы: