Triple S JAGUAR 20R, Руководство пользователя

Страница: 22 / 60

19
OVER VOLTAGE FAULT
UNDER VOLTAGE FAULT
tube
Insufficient suction, the floor cannot be
dried
Recovery tank is full Empty the recovery tank
Drain hose and squeegee poor
connection Connect the drain hose and
squeegee correctly
Float ball filter block
Clean the float ball filter and check
the float ball position status
Squeegee is dirty or wearing Check and clean the squeegee
The recovery tank cover is not closed
properly, or the gasket
is damaged, or
the Bend tube is clogged
Close the cover correctly, or re-
place the
gasket or clean the Bend
The Recovery tank is dirty Clean the recovery tank
Insufficient solution supply to brush
plate
The solution filter is dirty Clean the filter
The solution tank empty indicator is on Fill the solution tank
The solution tank is too dirty Clean the solution tank
Squeegee leaves scratch on the floor
There are debris under the squeegee
blade
Remove the debris
Squeegee blade wear, crack, aged Replace the squeegee blades
The squeegee balance is not adjusted Adjust the squeegee balance
Drive motor brake failure The brake is locked Set the brake unstuck
DRIVE MOTOR ERROR INDICATOR INFORMATION
LED CODES FAULT POSSIBLE CAUSE
1.1
¤¤
THERMAL FAULT
1. Temperature >80°C or < -10°C.
2. Excessive load on vehicle.
3. Operation in extreme environments.
4. Electromagnetic brake not releasing.
1.2
¤¤¤
THROTTLE FAULT
1. Throttle input wire open or shorted.
2. Throttle pot defective.
3. Wrong throttle type selected.
1.3
¤¤¤¤
SPEED POT FAULT
1. Speed limit pot wire(s) broken or shorted.
2. Broken speed limit pot.
1.4
¤¤¤¤¤
1. Battery voltage <17 volts.
2. Bad connection at battery or controller.
1.5
¤¤¤¤¤¤
1. Battery voltage >31 volts.
2. Vehicle operating with charger attached.
3. Intermittent battery connection.
2.1
¤¤¤
MAIN OFF FAULT
1. Main contactor driver failed open.
2.3
¤¤¤¤¤
MAIN FAULT
❊
1. Main contactor welded or stuck open.
2. Main contactor driver fault.
2.4
¤¤¤¤¤¤
MAIN ON FAULT
1. Main contactor driver failed closed.
3.1
¤¤¤¤
WIRING FAULT
❊
1. Misadjusted throttle.
2. Broken throttle pot or throttle mechanism.
3.2
¤¤¤¤¤
BRAKE ON FAULT
1. Electromagnetic brake driver shorted.
2. Electromagnetic brake coil open.
3.3
¤¤¤¤¤¤
PRECHARGE FAULT
❊
1. Brake driver shorted.
2. Precharge circuit damaged.
3. MOSFET failure.
3.4
¤¤¤¤¤¤¤
BRAKE OFF FAULT
1. Electromagnetic brake driver open.
2. Electromagnetic brake coil shorted.
3.5
¤¤¤¤¤¤¤¤
HPD FAULT
1. Improper sequence of throttle and KSI, push,
or inhibit inputs.
2. Misadjusted throttle pot.
4.1
¤¤¤¤¤
CURRENT SENSE FAULT
❊
1. Short in motor or in motor wiring.
2. Controller failure.
4.2
¤¤¤¤¤¤
HARDWARE FAILSAFE
❊
1. Motor voltage does not correspond to throttle
request.
2. Short in motor or in motor wiring.
3. Controller failure.