Page 66
E Series Ethernet Radio – User Manual
ER45e
Radio
Frequency Range:
370-520 MHz
(various sub-frequency
bands available)
Frequency Splits:
Various Tx/Rx
frequency splits - programmable
Channel Selection:
Dual synthesizer,
6.25 kHz channel step
Channel Spacing:
12.5 or 25 kHz
Frequency Accuracy:
±1ppm (-30 to
+60C)(-22 to 140F) ambient
Ageing:
<= 1ppm/annum
Operational Modes:
Simplex, Half
duplex or Full duplex*
Configuration:
All configuration via
Windows based software
Compliances:
ETSI
EN300113, EN301489,
EN60950
FCC
PART 15, PART 90
IC
RS119, ICES-001
ACA
AS4295-1995 (Data)
CSA
Class I, Division II, Groups
(A,B,C,D) for Hazardous
Locations ANSI/UL
equivalent) Pending.
Transmitter
Tx Power:
0.05 - 5W (+37 dBm)
1 dB User configurable with
over-temperature and reverse
power protection
Modulation:
User configurable
narrow band digitally filtered binary
GMSK or 4 level FSK
Timeout Timer:
Programmable
0-255seconds
Tx Spurious:
<= -37 dBm
PTT Control:
Auto (Data) / RTS line
on Data Port / System Port Override
Receiver
Sensitivity:
-118 dBm for
12 dB SINAD
Selectivity:
Better than 60 dB
Intermodulation:
Better than 70 dB
Spurious
Response: Better
than 70 dB
AFC Tracking:
Digital receiver
frequency tracking
Mute:
Programmable digital mute
Diagnostics
TVIEW+™
Configuration, Network
Management and Diagnostic
Windows GUI Software
Network wide operation from any
remote terminal.
Non intrusive protocol - runs
simultaneously with the application.
Over-the-air re-configuration of
user parameters.
Storage of data error and channel
occupancy statistics.
In-built Error Rate testing capabilities.
Connections
User Data Ports:
1 x RS232 DB9
female DCE. 300-38,400 bps.
System Port:
1 x RJ45 for diagnostic,
configuration and re-programming.
Ethernet Port:
10/100 Mbps (auto-
MDIX sensing) compliant with
IEEE 802.3
Antenna:
N female bulkhead.
Separate N (Tx) and SMA (Rx)
connectors for full duplex.*
Power:
2 pin locking, mating
connector supplied
LED Display:
Multimode Indicators
for Pwr, Tx, Rx, Sync, TxD and RxD
data LEDs and LAN LEDs
Ethernet
Protocols:
Ethernet/IP (including UDP,
TCP, DHCP, ARP, ICMP, STP, IGMP,
SNTP & TFPT)
Terminal Server:
Legacy RS-232
serial support via embedded terminal
server (UDP/TCP).
DHCP Modes:
Auto and Manual
Telnet:
Telnet access to programming
and diagnostics interface.
SNMP
: SNMP V1/V2 access to
diagnostics and radio information
Security
Encryption:
128-bit AES encryption**
Authentication:
Optional Trusted
radio authentication using Radius
compliant server
Modem
Data Port:
RS232, DCE,
300-38,400 bps asynchronous
System Port:
RS232, 19,200 bps
asynchronous
Flow Control:
Selectable hardware /
software / 3 wire interface
RF Channel Data Rate:
4800/9600/19,200 bps
Half / Full duplex*
Bit Error Rate:
< 1x10-6 @ -111 dBm (4800 bps)
< 1x10-6 @ -110 dBm (9600 bps)
< 1x10-6 @ -106 dBm (19,200 bps)
Please check with your local TRIO Datacom
representative.
Collision Avoidance:
TRIO Datacom’s
unique supervisory ChannelShare™
collision avoidance system
MultiStream™:
TRIO Datacom’s
unique simultaneous delivery of
multiple data streams (protocols)
Data Turnaround Time:
<10mS
Firmware:
upgradable flash based
firmware.
Local regulatory conditions may determine the
performance and suitability of individual versions
in different countries. It is the responsibility of
the buyer to confirm these regulatory conditions.
Performance data indicates typical values related
to the described unit.
Information subject to change without notice.
© Copyright 2010 TRIO Datacom Pty Ltd.
All rights reserved. Issue 08-2010
** Export restrictions may apply
Note: Not all product features are available
in every mode of operation.
General
Power Supply:
13.8 Vdc nominal
(10-30 Vdc)
Temp Range:
-30degC to +60degC
Transmit Current:
750 mA nom. @ 1 W
1600 mA nom. @5 W
Receive Current:
<180mA nom
Shutdown Mode:
External control,
< 10 mA
Housing:
Rugged Diecast Enclosure
Dimensions:
170 x 150 x 42mm
6.7 x 5.9 x 1.65 inches
With Mounting Plate
190 x 150 x 47mm
7.5 x 5.9 x 1.85 inches
Mounting:
Fitted Mounting Plate or
DIN rail
Weight:
1.27 kg (2.8lbs.)
Options
ERFD45e
Full Duplex Operation
with separate N (Tx) and SMA
(Rx) connectors
DIN Rail mounting kit
Part Number : ER-DIN-KIT*
*Not offered in all countries.
Related Products
EB45
e
Base Station
EH45
e
Hot Standby Base Station
MSR/9 Port Stream Router Multiplexer
MR450 Remote Data Radio
* With ERFD450 full duplex option plus
external duplexer for single antenna
operation
This device is OPEN type equipment that must be used within
a suitable end-use system enclosure, the interior of which is
accessible only through the use of a tool. The suitability of
the enclosure is subject to investigation by the local Authority
Having Jurisdiction at the time of installation.
