Trinamic TMCM-1240 Скачать руководство пользователя страница 27

Страница: 27 / 30

TMCM-1260 Hardware Manual • Hardware Version V1.10 | Document Revision V1.20 • 2018-05-17

27 / 30

14 Tables Index

TMCM-1260 Order Code

. . . . . . . .

TMCM-1260 Cable Loom

. . . . . . . .

Connector Types and Mating Connec-

tors of the TMCM-1260

. . . . . . . . .

Power Supply Connector Pin Assignment

Motor Connector Pin Assignment

. .

RS485 + CAN Connector Pin Assignment

USB Connector Pin Assignment

. . . .

I/O Connector Pin Assignment

. . . .

10 Available motor current settings

. . .

11 General operational ratings of the

module

. . . . . . . . . . . . . . . . . .

12 Operational ratings of I/Os

. . . . . .

13 Operational ratings of the RS485 inter-

face

. . . . . . . . . . . . . . . . . . . .

14 Operational ratings of the CAN interface

15 Abbreviations used in this Manual

. .

16 Hardware Revision

. . . . . . . . . . .

17 Document Revision

. . . . . . . . . . .

Terms of delivery and rights to technical change reserved.

Download newest version at

www.trinamic.com

Содержание TMCM-1240































Результаты поиска

Содержание TMCM-1240

Отзывы:

Бренды по названию

Популярные бренды

Trinamic TMCM-1240, Руководство по оборудованию

Результаты поиска

Содержание TMCM-1240

Отзывы:

Бренды по названию

Популярные бренды