Trinamic TMCM-1240 Скачать руководство пользователя страница 20

Страница: 20 / 30

TMCM-1260 Hardware Manual • Hardware Version V1.10 | Document Revision V1.20 • 2018-05-17

20 / 30

9 Motor driver current

The on-board stepper motor driver operates current controlled. The driver current may be programmed

in software with 32 effective scaling steps in hardware.

Explanation of different columns in table below:

Motor current set-

ting in software

(TMCL)

These are the values for TMCL axis parameter 6 (motor run current) and

7 (motor standby current). They are used to set the run / standby current

using the following TMCL commands:

SAP 6, 0, <value> // set run current
SAP 7, 0, <value> // set standby current

(read-out value with GAP instead of SAP. Please see separate TMCM-1260

ﬁrmware manual for further information)

Motor current I

RMS

[A]

Resulting motor current based on motor current setting

Available motor current settings

Motor current setting

in software (TMCL)

Current scaling step

(CS)

Motor current I

COIL

[A]

peak

Motor current I

COIL

[A]

RMS

0. . . 7

0.254

0.180

8. . . 15

0.508

0.359

16. . . 23

0.762

0.539

24. . . 31

1.016

0.718

32. . . 39

1.270

0.898

40. . . 47

1.523

1.077

48. . . 55

1.777

1.257

56. . . 63

2.031

1.436

64. . . 71

2.285

1.616

72. . . 79

2.539

1.795

80. . . 87

2.793

1.975

88. . . 95

3.047

2.154

96. . . 103

3.301

2.334

104. . . 111

3.555

2.514

112. . . 119

3.809

2.693

120. . . 127

4.063

2.873

128. . . 135

4.316

3.052

136. . . 143

4.570

3.232

144. . . 151

4.824

3.411

152. . . 159

5.078

3.591

Terms of delivery and rights to technical change reserved.

Download newest version at

www.trinamic.com

Содержание TMCM-1240































Результаты поиска

Содержание TMCM-1240

Отзывы:

Бренды по названию

Популярные бренды

Trinamic TMCM-1240, Руководство по оборудованию

Результаты поиска

Содержание TMCM-1240

Отзывы:

Бренды по названию

Популярные бренды