Trinamic TMCM-1211 TMCL Скачать руководство пользователя страница 112

Страница: 112 / 133

TMCM-1211 TMCL

™

Firmware Manual • Firmware Version V1.10 | Document Revision V1.00 • 2018-OCT-02

112 / 133

Number

Global Parameter

Description

Range [Units]

Access

Serial secondary

address

Second module (target) address for RS485.

Setting this parameter to 0 switches off the

seconndary address.

0. . . 255

RWA

128

TMCL application

status

0 - stop

1 - run

2 - step

3 - reset

0. . . 3

129

Download mode

0 - normal mode

1 - download mode

0/1

130

TMCL program

counter

Contains the address of the currently exe-

cuted TMCL command.

132

TMCL tick timer

A 32 bit counter that gets incremented by

one every millisecond. It can also be reset

to any start value.

0. . . 2147483647

133

Random number

Returns a random number. The seed value

can be set by writing to this parameter.

0. . . 2147483647

255

Suppress reply

The reply in direct mode will be suppressed

when this parameter is set to 1. This pa-

rameter cannot be stored to EEPROM and

will be reset to 0 on startup. The reply will

not be suppressed for GAP, GGP and GIO

commands.

0/1

Table 18: All Global Parameters of the TMCM-1211 Module in Bank 0

5.2

Bank 1

The global parameter bank 1 is normally not available. It may be used for customer speciﬁc extensions

of the ﬁrmware. Together with user deﬁnable commands these variables form the interface between

extensions of the ﬁrmware (written by Trinamic in C) and TMCL applications.

5.3

Bank 2

Bank 2 contains general purpose 32 bit variables for use in TMCL applications. They are located in RAM

and the ﬁrst 56 variables can also be stored permanently in the EEPROM. After booting, their values are

automatically restored to the RAM. Up to 256 user variables are available. Please see table

for an

explanation of the different parameter access types.

User Variables in Bank 2

Number

Global Parameter

Description

Range [Units]

Access

0. . . 55

user

variables

#0. . . #55

TMCL user variables

-2147483648 . . .

2147483647

RWE

56. . . 255

user

variables

#56. . . #255

TMCL user variables

-2147483648 . . .

2147483647

RWE

Table 19: User Variables in Bank 2

Terms of delivery and rights to technical change reserved.
Download newest version at

www.trinamic.com

Содержание TMCM-1211 TMCL






































































































































Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Похожие инструкции для TMCM-1211 TMCL

Бренды по названию

Популярные бренды

Trinamic TMCM-1211 TMCL, Руководство по прошивке

Результаты поиска

Содержание TMCM-1211 TMCL

Отзывы:

Похожие инструкции для TMCM-1211 TMCL

Бренды по названию

Популярные бренды