Trimline 38 FS Скачать руководство пользователя страница 15

 

Trimline 38 FS

Installation instruction

15

8.5 Installation

  Guide the flexible hose (6) through the existing flue (7).

  Attach the slider (5) to the bottom of the flexible hose 

and secure this in place using two Parker screws.

  Keep the bottom of the slider at the same height as 

the bottom of the flue or ceiling. Shorten the flexible hose 
to approximately 100mm above the chimney coping.

  Attach the mounting plate to the flexible hose on the roof 

(8), clamp it with a hose bracket. Stainless steel Ø90 to 165, 
secure the whole with Parker screws.

  Attach the mounting plate to the chimney coping watertight 

on the roof (8) using silicone sealant and stainless steel 
screws.

  Install the roof pass-through (9) and secure it in place using 

the supplied clamping strip (10).

  The slider (5) will protrude approximately 100mm 

underneath the flue or ceiling after installation.

  Attach the inner mounting plate (4) gastight against 

the bottom of the structural flue or against the bottom of 
the concrete floor using silicone sealant and screws.

  Position the unit in accordance with the instructions of 

the unit manufacturer

  Install a minimum of 1 metre of concentric flue type 

THC CC (2).

  Extend the concentric flue using sections (2) up to 

a minimum of 100mm in the structural duct. Finally, turn 
the clamping strip by hand in the mounting plate inside (3).

Содержание 38 FS























Отзывы: