Trilithic 180 DSP Скачать руководство пользователя

Страница: 90 / 386

www.trilithic.com

Page II-25

180 DSP Operation Manual

Signal Level Meter

LCD Dimming Delay

The

LCD Dimming Delay

setting is

used to conserve power by automatically

dimming the display screen backlight after

the 180 DSP has been idle for a specified

period of time.
The default setting for the LCD dimming

delay is

1 Minute

. The LCD dimming

delay can be set from a minimum of one

(1) minute up to a maximum of five (5)

minutes.
Use either of the following methods to

change the LCD dimming delay:

• Use the up/down arrow buttons to

change the value in one (1) minute

increments.

• Press the

Enter

button and use the

Virtual Keyboard

to directly enter

the LCD dimming delay as shown

in the image to the right.

Upon any button press, the LCD will automatically brighten and the delay timer will restart.

Whenever the 180 DSP is being powered by the AC to DC

power adapter & battery charger, the LCD dimming delay will

be deactivated automatically.

Содержание 180 DSP



































































































































































































































































































































































































Результаты поиска

Содержание 180 DSP

Отзывы:

Похожие инструкции для 180 DSP

Бренды по названию

Популярные бренды

Trilithic 180 DSP, Руководство по эксплуатации

Результаты поиска

Содержание 180 DSP

Отзывы:

Похожие инструкции для 180 DSP

Бренды по названию

Популярные бренды