Trilithic 180 DSP Скачать руководство пользователя

Страница: 327 / 386

www.trilithic.com

Page IV-131

180 DSP Operation Manual

Signal Level Meter

Ping Mode

When the

Ping

mode is selected, the

following measurement results are

displayed as shown in the image to the

right:

• Minimum Time

- This is the

minimum time required to send/

receive a single test packet.

• Average Time

- This is the average

time required to send/receive all

test packets.

• Maximum Time

- This is the maximum time required to send/receive a single test

packet.

• Sent

- This is the number of packets sent by the 180 DSP to the destination IP

address.

• Received

- This is the number of packets received by the 180 DSP from the

destination IP address.

• LPR

- This is the lost packet ratio. This measurement is displayed in the bar graph

and as a numeric value. The LPR is calculated as the percentage of packets

received to those which were sent (LPR = {Received Packets / Sent Packets} *

100%), for example:

•  50 sent packets
•  25 received packets
•  LPR = {25 / 50} * 100%

{0.50} * 100%

50%

Содержание 180 DSP



































































































































































































































































































































































































Результаты поиска

Содержание 180 DSP

Отзывы:

Похожие инструкции для 180 DSP

Бренды по названию

Популярные бренды

Trilithic 180 DSP, Руководство по эксплуатации

Результаты поиска

Содержание 180 DSP

Отзывы:

Похожие инструкции для 180 DSP

Бренды по названию

Популярные бренды