TRIGA TR-FFT Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 33

TRIGA TR-FFT Скачать руководство пользователя страница 14

14

PRELIMINARY: TR-FFT Fire Fighter’s Telephone Manual — LS10309-001TR-E:A 04/28/2021

Installation

Fire Fighter’s Handset Installation

Cabinet Door and Dead Front Removal

When you install the cabinet, it may be necessary to remove the cabinet door and the dead front panel. This Section provides

instructions on how to remove the cabinet door and the dead front panel.
1. Using a Phillips head screwdriver, remove the six screws that hold the dead front panel in place. See Figure 3.4.

.

Figure 3.4 Cabinet Door and Dead Front Panel Removal

2. Using a 1/4”(.64cm) hex drive, remove the six hex nuts that hold the cabinet door in place. See Figure 3.4.



Re-Attaching the Cabinet Door

To re-attach the cabinet door, refer to the procedure in Section 3.

3.2 Fire Fighter’s Handset Installation



TR-FFT Local Handset installation involves the following steps:

1. Insert the phone cord through the hole of the dead front panel. See Figure 3.5.

Figure 3.5 Handset Cord Inserted Through the Dead Front Panel Hole

2. Attach the strain relief clip to the phone cord. The strain relief clip should have about 2 ¾” (6.99cm) length of phone cord

through it. See Figure 3.6.

3. Push the strain into the hole in the dead front panel.

Cabinet Door

Dead

Front Panel

Dead Front

Panel Screws

Cabinet Door

Hex Nuts

Cabinet Door and Dead Front Removal

When you install the cabinet, it may be necessary to remove the cabinet door and the dead front panel. This Section provides

instructions on how to remove the cabinet door and the dead front panel.
1. Using a Phillips head screwdriver, remove the six screws that hold the dead front panel in place. See Figure 3.4.

.

Figure 3.1 Cabinet Door and Dead Front Panel Removal

2. Using a 1/4”(.64cm) hex drive, remove the six hex nuts that hold the cabinet door in place. See Figure 3.4.



Re-Attaching the Cabinet Door

To re-attach the cabinet door, refer to the procedure in Section 3.

Cabinet Door

Dead

Front Panel

Dead Front

Panel Screws

Cabinet Door

Hex Nuts

«
...
12
13
14
15
16
...
»

Содержание TR-FFT


































Отзывы:

Нет отзывов