manualshive.com logo in svg

Tridium JACE-6 Series, Монтаж и подключение

Поделиться
Скачать
Tridium JACE-6 Series Скачать руководство пользователя страница 9

 

Wiring Details

Grounding

JACE-6 Mounting and Wiring Instructions

Part Number 10821

Published: April 19, 2007

9

Wiring Details

See 

Figure 2

 on page 6 to locate connectors and other components on the JACE-6 controller. 

Make connections to the JACE in the following order.

1.

Install any option boards (LON, RS-485, RS-232, or modem) in option slots 1 and 2. See 

“Mounting 

Option Cards,”

 page 7 for a general procedure. For complete details, refer to the specific mounting and 

wiring guide that shipped with the option board.

2.

Connect supplied earth grounding wires (with spade connector) from the earth ground lug on the JACE-6 
and any accessory modules (if used) to a nearby earth grounding point. See 

“Grounding”

 for details.

3.

Prepare power wiring (leave the unit powered off). See 

“Power Wiring”

 for details.

4.

Connect communications cables. See 

“Communications Wiring,”

 page 12 for ports available on the 

JACE-6 base unit. For ports on any installed option board (LON, RS-485, modem) see the specific 
mounting and wiring guide for any additional details.

5.

If IO accessory modules are installed, connect the I/O wiring. Refer to the appropriate mounting and 
wiring guide for complete details.

6.

Connect the backup battery to the JACE-6 battery connector, and apply power to the unit. See 

“Power Up 

and Initial Checkout,”

 page 15.

Grounding

An earth ground spade lug (0.187") is provided on the base of the JACE-6 for connection to earth ground. For 
maximum protection from electrostatic discharge or other forms of EMI, connect the supplied earth grounding 
wire to this lug and a nearby earth ground (see 

Figure 3

 on page 11). Keep this wire as short as possible.

Power is provided for JACE-6 plug-in accessory modules through the 20-pin accessory connectors. However, 
you should also connect the earth ground spade lug of 

each accessory module

 to ground in the same manner.

IO-16

DIN-mountable, 16 points I/O module, 
used to provide I/O points as noted.

Provides the following I/O points:
• 8 - Universal Inputs (UIs).
• 4 - Digital Outputs (DOs), SPST-relay type.

• 4 - Analog Outputs, 0–10Vdc type.

Up to four (maximum) IO-16 accessory modules are supported.

Wiring is covered in a 

separate

 document, see the

 

IO-16 Installation and Configuration Instructions

.

IO-34

(available only 

in some 

markets)

DIN-mountable, combined 34 points I/O 
with 24V isolated power module, used to 
provide I/O points as well as power 
JACE-6 from a dedicated, external, 
Class-2, 24Vac transformer 

or

 a 24Vdc 

power supply.

Only one IO-34 per JACE-6. Provides the following I/O points:
• 16 - Universal Inputs (UIs).
• 10 - Digital Outputs (DOs), SPST-relay type.

• 8 - Analog Outputs, 0–10Vdc type.

Up to 2 additional IO-16 modules can be used. Do not power the 
IO-34 if using 

WPM-XXX

.

Wiring is covered in a 

separate

 document, see the

 

IO-34 Installation and Configuration Instructions

.

Table 2

JACE-6 accessory modules. (continued)

Model

Description

Notes

Содержание JACE-6 Series

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды