Tridium JACE-6 Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 24

Tridium JACE-6 Series Скачать руководство пользователя страница 15

Power Up and Initial Checkout

Connect the Backup Battery

JACE-6 Mounting and Wiring Instructions

Part Number 10821

Published: April 19, 2007

15

Power Up and Initial Checkout

Ensure power wiring to the JACE-6

is ready—see the

“Power Wiring”

section on page 10. Refer to

page 6 for the locations of the JACE-6 battery connector, status LEDs and barrel power connector (for
WPM-

XXX

only). Refer to

on page 11 for location of the power connector on the

module.

Following all mounting and wiring, perform the following:

Procedure 4

Initial power up and checkout

Step 1

Connect the Backup Battery

.

Step 2

.

Step 3

Check the Status LEDs

Connect the Backup Battery

With the cover removed from the JACE-6 (see

“Removing and Replacing the Cover,”

page 6), locate the red

and black wires coming from the backup battery, with 2-position connector plug. Insert the plug into the battery
connector on the bottom board (below option slot 2 area), as shown in

.

Figure 6

Backup battery connector on JACE-6 bottom board.

The connector is keyed—you cannot insert it incorrectly. The red (positive) connection should be the furthest
from the two 30-pin option board connectors. For more battery details, see

“About the Battery,”

Apply Power

Apply power to the JACE-6 by plugging in the power plug into either the JACE-6 (if wall mount AC adapter

) or the 24V-powered

module. If powering using the line-voltage input NPM-PWR-UN

power supply module, energize the 90–263 Vac circuit wired to the NPB-PWR-UN module.

Caution

Do not connect

both

the WPM-

XXX

and NPB-PWR / NPB-PWR-UN supplies at the same time, or

equipment damage may result, or a power outage may go unrecognized.

Battery
Connector

Battery
Assembly

«
...
13
14
15
16
17
...
»

Содержание JACE-6 Series

























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды