manualshive.com logo in svg

Tridium JACE-6 Series, Монтаж и подключение

Поделиться
Скачать
Tridium JACE-6 Series Скачать руководство пользователя страница 11

 

Wiring Details

Power Wiring

JACE-6 Mounting and Wiring Instructions

Part Number 10821

Published: April 19, 2007

11

Note

If powering from a 24V transformer, do 

not

 power any other equipment with it. Otherwise, conducted 

noise problems may result. Also, do not ground either side of the transformer’s 24V secondary.

Figure 3

NPB-PWR module wiring connections.

Located at the bottom of the NPB-PWR module is a 2-position power connector, and an earth ground spade lug, 
as shown in 

Figure 3

.

Connect the supplied earth ground wire to a nearby earth ground point. Unplug the power connector plug from 
the module and make connections to it as shown in 

Figure 3

.

Caution

Do not plug 24V power into the NPB-PWR (reinsert connector plug) until all other mounting and 
wiring is completed. See 

“Power Up and Initial Checkout,”

 page 15.

Power consumption depends on installed accessories and option boards, and may vary from:

•

JACE-6 with NPB-PWR module alone: approximately 8.5 VA (AC) or 8.5 W (DC)

•

JACE-6 with NPB-PWR and four (4) IO-16 modules, plus option boards: up to 20 VA (AC) or 20 W (DC)

NPB-PWR-UN

The NPB-PWR-UN module lets you power the JACE-6 (and if installed, IO-16 modules) from AC line power, 
with a universal input range from 90–263Vac. If installing IO-16 modules, the NPB-PWR-UN installs as the 

last

 

(end) module in the chain. See 

Figure 1

 on page 5.

Warning

•

A 120Vac or 240Vac circuit powers the NPB-PWR-UN. 

Disconnect power

 to this circuit 

before installation to prevent electrical shock of equipment damage.

•

Make all connections in accordance with national and local electrical codes. Use copper 
conductors only.

•

Do not exceed the 30W capacity of NPB-PWR-UN by the powered devices.

+

–

NPB-PWR (cover shown removed)

JACE-6

24Vac

Line Voltage

(Mains)

Earth Ground

or

Dedicated 24Vac Transformer
neither side of secondary tied 
to earth ground

24Vdc

24Vdc 

Power Supply

(Polarity Not Critical)

neither side tied to earth

Содержание JACE-6 Series

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды