RECHARGING THE BATTERIES
The batteries must be charged prior to first use, and whenever they no longer provide sufficient
power.
ATTENTION
: to avoid any permanent damage to the batteries, it is essential to avoid their
complete discharge; begin recharging them within a few minutes of noting the "discharged
batteries" signal.
ATTENTION
: never leave the batteries completely discharged, even if the device is not being
used.
1. Bring the appliance to the area where the batteries are charged.
2. Make sure the machine is in a safe condition (see “
MACHINE SAFETY MEASURES
”).
ATTENTION
: park the machine in an enclosed place, on a flat and level surface; near the
machine there must be no objects that could either damage it, or be damaged through contact
with it.
ATTENTION
: the room used to recharge the batteries must be adequately ventilated to prevent
the accumulation of gases that leak from batteries.
3. Grip the handle (1) on the right-hand side of the recovery tank (
Fig.1
) and turn the tank as far as
it will go, until it reaches the maintenance position.
ATTENTION
: the following operations must be carried out by qualified personnel. An incorrect
connection of the connector may cause a malfunction of the device.
NB
: carefully read the use and maintenance instructions of the battery charger used.
4. Go to the back of the machine and remove the cap (2) from the battery charger socket (
Fig.2
).
5. Connect the battery charger power cable connector (3) to the battery charger socket (4) (
Fig.3
).
CAUTION
: before connecting the batteries to the battery charger, make sure it is suitable for
the batteries used.
WARNING
: before inserting the connector (3) in the socket (4), make sure there is no
condensation or any other type of liquid.
NB
: the battery charger power cable is delivered inside the bag containing this instruction
booklet.
6. Plug the battery charger cable into the mains socket.
CAUTION
: keep the recovery tank open for the duration of the battery recharging cycle to
allow gas fumes to escape.
NB
: before connecting the battery charger to the mains socket, make sure the characteristics
of the mains supply correspond to those required by the battery charger. Read the battery
charger use and maintenance manual (included in the bag that contains this instruction
booklet).
7. When the recharge cycle is complete, disconnect the battery charger cable from the mains.
8. Disconnect the battery charger power cable from the socket on the battery charger itself.
9. Replace the cap (2) on the battery charger plug.
10. Grip the handle (1) on the right-hand side of the recovery tank and turn the tank as far as it will
go, until it reaches the maintenance position.
ASSEMBLING THE BRUSH
For packaging reasons, the brush is supplied disassembled from the device. To assemble it on the
brush head body, proceed as follows:
1. Make sure the electric brake is engaged, then rotate the lever (1) anti-clockwise. The lever is
located on the rear right-hand side of the machine (
Fig.1
).
2. Make sure the recovery tank is empty. If it isn't, empty it using the tube (2) on the rear left-hand
side of the machine (
Fig.2
) (see "
EMPTYING THE RECOVERY TANK
").
ATTENTION
: the tanks should be emptied in the place used for draining dirty water.
ATTENTION
: the place designated for this operation must comply with current environmental
protection regulations.
CAUTION:
users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
3.
Switch on the machine by turning the main switch (3) to "I", making a quarter turn of the key in
the direction of the arrow (
Fig.3
).
4. Lift the brush head body and press the “BRUSH HEAD CONTROL” button (4) on the control
panel (
Fig.4
).
NB
:
as soon as the button (4) on the control panel is pressed, the green LED (5) (“BRUSH
HEAD BODY WORK POSITION”) will switch off (
Fig.4
).
5.
Switch off the machine by turning the main switch (3) to "0", making a quarter turn of the key in
the direction of the arrow (
Fig.5
). Remove the key from the instrument panel.
6. Raise the squeegee body and turn the squeegee control lever (6) in the direction of the arrow
(
Fig.6
). The lever is located on the back of the machine.
7. Grip the handle (7) on the right-hand side of the recovery tank (
Fig.7
) and turn the tank as far as
it will go, until it reaches the maintenance position.
8. Disconnect the electrical system connector (8) from the battery connector (9) (
Fig.8
).
ATTENTION
: this process must be carried out by qualified personnel.
9. Grip the handle (7) on the right-hand side of the recovery tank and turn the tank as far as it will
go, until it reaches the work position.
ATTENTION
: make sure the battery charger supply cable is disconnected from the mains
socket.
10. With the brush head up, insert the brush in the plate housing underneath the brush head, turning
it until the three buttons engage with the notches on the plate itself (
Fig.9
).
11. Turn until the pin is pushed towards the coupling spring and is locked into place.
12. Grip the handle (7) on the right-hand side of the recovery tank and turn the tank as far as it will
go, until it reaches the maintenance position.
13. Connect the electrical system connector (8) to the battery connector (9) (
Fig.8
).
ATTENTION
: this process must be carried out by qualified personnel.
14. Grip the handle (7) on the right-hand side of the recovery tank and turn the tank as far as it will
go, until it reaches the work position.
15
CONNECTING THE BATTERIES TO THE MACHINE SYSTEM
The batteries should be connected so as to obtain a
total voltage of 24V.
ATTENTION
: it is recommended that all
installation and maintenance operations be
carried out by expert personnel, trained at the
specialised assistance centre.
CAUTION
: to prevent an accidental short circuit
use insulated tools to connect the batteries, and
do not place or drop metal objects on the battery.
Remove rings, watches and any clothing with
metal parts that may come into contact with the
battery terminals.
The various phases for inserting the batteries in the battery compartment are as follows:
1.
Using the supplied jumper cable (1), connect the batteries to the "+" and "-" poles in sequence.
2. Connect the batteries' connector cable (2) to the “+” and “-“ poles to obtain a voltage of 24V at
the terminals.
3. Connect the electric system connector (3) to the battery connector (2).
2
3
1
7
7
2
3
1
1
2
4
3
2
3
1
3
1
2
8
5
3
4
5
4
6
6
9
7
7
8
8
9
Содержание T20SC PRO
Страница 2: ......
Страница 26: ...NOTES 26 ...
Страница 27: ......
Страница 28: ...HILLYARD INDUSTRIES PO Box 909 St Joseph Missouri 64502 0909 U S A Telephone 816 233 1321 www hillyard com ...