Trianco Aztec Classic WM Maxi Combi Скачать руководство пользователя страница 24

Страница: 24 / 25

Aztec Commissioning Report

Commission Details

Date of Completion: ________________________ Date of Commission: ______________________

Serial Number: _________________________________________________________

RCD

Existing/New: ________________________ Size: _________

Supply Cable

Existing/New: _________

Diameter (mm): __________

Isolation valves fitted to all boiler outlets Y/N______________

Magnetic Filter Fitted to Heating circuit Y/N______________

In-line scale inhibitor fitted Y/N______________

Incoming Cold-Water Pressure ______________Bar

What is the maximum Hot water flow rate set at? _________l/min

Has the strainer been cleaned of installation debris Y/N __________

What is the hot water temperature at the nearest outlet? __________°C

All appropriate pipes have been insulated __________

The tundish and discharge pipework have been connected and terminated to Part G of the building regulations _________

Where is the pressure reducing valve situated ________________________________

The hot water system complies with the appropriate Building Regulations _________

By signing you agree that you have installed the boiler in accordance with these instructions and that the boiler is working as
intended.

Plumber

Signed: ________________________ Date: __________________________

Electrician

Signed: ________________________ Date: ___________________________

Customer Acceptance

I confirm that I have received training and instruction on how to operate and maintain this appliance.
I understand the warranty on this product, and I have been provided with a User Manual and Operating Instructions.

Customer Signature: ____________________________________

Date: _____________________

Installation Details

Name:
Address: ______________________________________
______________________________________________

______________________________________________
Tel:

_______________________________

Mobile No:

_______________________________

Email:

_______________________________

Commissioning Engineer Details

Name:
Address: ______________________________________
______________________________________________

BPEC G3 CERT No _______________________________
Tel:

_______________________________

Mobile No:

________________________________

Email:

_______________________________

Содержание Aztec Classic WM Maxi Combi


























Результаты поиска

Содержание Aztec Classic WM Maxi Combi

Отзывы:

Похожие инструкции для Aztec Classic WM Maxi Combi

Бренды по названию

Популярные бренды

Trianco Aztec Classic WM Maxi Combi, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Aztec Classic WM Maxi Combi

Отзывы:

Похожие инструкции для Aztec Classic WM Maxi Combi

Бренды по названию

Популярные бренды